msp430f149键盘中断程序，用端口中断。通过实验验证

ARM单片机应用开发指南(S3C4510B)-ARM MCU Application Development Guide (S3C4510B)

MSP430仿真器原理图，Msp430仿真器原理图，我做了好使-MSP430 simulator schematics, Msp430 simulator diagram, I have done so

利用动态扫描和定时器1在数码管上显示 出从765432开始以1/10秒的速度往下递减 直至765398并保持显示此数，与此同时利 用定时器0以500MS速度进行流水灯从上至 下移动，当数码管上数减到停止时，实验 板上流水灯也停止然后全部开始闪烁，3秒 后（用T0定时）流水灯全部关闭、数码管上 显示出"HELLO"。到此保持住。 设晶振频率为12MHz。-The use of dynamic scanning and Timer 1 in the digital control to show from the beginning of 765,432 to 1/10 seconds until the speed of descending down 765,398 and maintain display this number, at the same time the use of Timer 0 to 500ms the speed of light from the flowing water to Under the move, when reduced to a few digital tube stop, the experiment on-board water stop and then all the lights started to flicker, 3 seconds later (T0 regularly used) closed water lights, digital tubes show

C8051 link philips TV tuner.

TI公司的MSP430F1611单片机的液晶显示程序-TI

单片机系统上电后，P0 口和 P1 口都被清 0。然后，你规定一个由 6 个数字构成的序列（每个数字从 0～F 中选取），比如 E、8、9、0、7、F。然后每次当单片机检测到外部中断 0发起中断时间时，读取 P0 口和 P1 口上的状态值，当连续 6 次外部中断事件的对应的数字序列构成你所设定的序列后（举例来说，如果 P0.0 是 1，P0 和 P1 的其他管脚是 0，那么我们称为检测到一次数字 0），从串口打印输出一幅类似下图的 16×16 的ASCII码的圣诞树图片。-Single-chip microcomputer system after power, P0 and P1 mouth I have been ching 0. Then you set a six figure constituted by the sequence (each number from 0 ~ F in selected), for example, E, 8,9,0,7, F. And then each time a single-chip detects external interrupt 0 initiated interruption time, I read the P0 and P1 mouth on the state value, when a row 6 times the corresponding external interrupt events constitute digital sequence set your sequence (for example example, if P0.0 is 1, P0 and P1 of the other pin is 0, then we called a number of detected 0), a printout from the serial port under similar 16 × 16 map of the ASCII code of the Christmas tree图片.

本程序运行于C8051F330，功能为接收遥控器发出的红外信号，然后等待上位机通过I2C总线来读取。IR数据接收完毕后，不再采集新的IR数据，一直等待上位机将数据取走后才开始准备接收新的IR数据-this program running on the C8051F330, functional remote control device to receive the infrared signal, Then wait for the PC through the I2C bus to read. IR data receiving end, not the acquisition of new IR data have been waiting for the PC will be removed after data began preparing to receive the new IR data

一个单片机温度控制的完整程序-a complete temperature control procedures

PIC LED 流水灯实验，顺闪，返闪，交替闪-PIC LED

非常有用的12864LCD功能驱动KEilC51的开发