VB平台单片机与PC机串口通信的PC端程序。小巧易用，功能丰富...

仿真步骤如下： 1、把3个帖子的内容分别保存为51t9py.c,51t9py_indexa.h,5py_mb.h，放在同一目录下，将51t9py.c加入工程编译 2、由于Keil的模拟串口是单字节显示，汉字显示为乱码，所以要加挂RICHWIN或RichView这种会重新刷新显示的中文平台，或手工刷新屏幕，所以请先到 http://www.pchome.net/dl/chinese.htm 下载RichView，安装运行 3、在Keil环境下可以直接按“Ctrl＋F5”键仿真，按“F5”全速运行，切换到在串口依次输入: // 64*.6 426***.5 98*.7 936.3 586.1 4826*.1 9464*.7 64*.6试试:-) 4、按键对应(根据我自己的手机设置的,全部在PC的小键盘操作)： -simulation steps are as follows : 1 and 3 respectively, the content of messages posted on the preservation of 51t9py.c, 51t9py_indexa.h, 5py_mb.h, on the same directory, will join the project 51t9py.c compiler 2, Keil is the simulation of single-byte Serial show , the Chinese showed gibberish, so need to add or RichView RICHWIN this show will re-set the Chinese platform, or manual refresh screen, so please download RichView http://www.pchome.net/dl/chinese.htm to install three operations in Central Keil Habitat can be directly "Ctrl+ F5" key simulation, according to the "F5" running full-speed, switched to the ser

PIC单片机的指令集，其中包括了12位（基本级）、14位（中、高级）产品的全部指令！-PIC microcontroller instruction set, which included a 12 (basic level), 14 (senior) products all directions!

SPI是一个环形总线结构，由ss（cs）、sck、sdi、sdo构成，其时序其实很简单，主要是在sck的控制下，两个双向移位寄存器进行数据交换。 假设下面的8位寄存器装的是待发送的数据10101010，上升沿发送、下降沿接收、高位先发送。 那么第一个上升沿来的时候 数据将会是sdo=1；寄存器=0101010x。下降沿到来的时候，sdi上的电平将所存到寄存器中去，那么这时寄存器=0101010sdi，这样在8个时钟脉冲以后，两个寄存器的内容互相交换一次。这样就完成里一个spi时序。 -SPI bus is a ring structure, by ss (cs), sck, sdi, sdo composition, its timing is actually very simple, mainly under the control of the sck and two bi-directional shift register for data exchange. Assuming the following 8-bit register is loaded to send the data to be 10,101,010, rising to send, receive falling edge, high first sent. Well, the first rising edge to the time data will be sdo = 1 register = 0101010x. Falling edge comes, sdi on the level will be stored to the register, then register at this time = 0101010sdi, so 8 clock pulse later, the contents of two registers to exchange time. This will be completed in a spi timing.

用于开发菲利浦XA单片机的开发环境，同时含注册方式-XA for the development of the Philips MCU development environment, including the registration form

广州周立功单片机举办的ARM免费培训（郑州站）内容简介-Guangzhou Zhou, who organized the ARM MCU free training (Zhengzhou station) Description

单片机原理与实用技术》第3章-SCM principles and practical technology, "Chapter 3

AD 转换 用定时器中断 显示 0--5V-AD0804 zhongduan xianshi

温度传感器18B20的典型应用，通过18B20采集温度，可以精确到小数点两位，在LED或LCD上显示-Temperature Sensors Typical applications 18B20, 18B20 collected through the temperature, can be accurate to two decimal places, in the LED or LCD display

用AVR单片机(ATMEGA8)编写的lcd AMPIRE128*64显示程序,用C语言编写,用GCCAVR开发,用proteus仿真通过.

有关的PIC的16F87XA的一些使用说明，供大家一起分享。-PIC-related 16F87XA of some use for everyone to share.