This is a tutorial for beginners SCM, easy to learn. Is the first choice for beg...

触摸屏基础知识大全与最新多点触摸屏技术介绍-多点位置识别-Basic knowledge of touch screen Guinness with the latest multi-point touch screen technology introduction- multi-point location identification

32 k eeprom c51 源程序 调试通过-32 k EEPROM decoder source debugging through

基于89S51的LED汉字显示,开发环境KEIL,仿真环境PROTEUS-89S51 based on the LED display of Chinese characters, development environment KEIL, simulation environment PROTEUS

这是关于DS18B20的读写程序,数据脚P2.2,晶振12MHZ温度传感器18B20汇编程序,采用器件默认的12位转化,最大转化时间750微秒特点能精确到0.5摄氏度-DS18B20 on literacy, data P2.2 feet, 12 MHZ crystal oscillator temperature sensor 18 B20 compilation procedures, devices using the default 12 conversion the largest 750 microsecond conversion time characteristics can be accurate to 0.5 degrees Celsius

///*** *** *** * //一、程序说明： //1, 24LC02器件地址是1010000R/W. //2, 数组写入24LC02采取页写方式. //3, 数组code从24LC02读出时采取自由读方式. //4, 采用4.00M晶体。 //5，采用软件I2C。 //二、硬件连接： //1， SDA------->23 pin.(当然你可以任意选择脚位） //2, SCL------->18 Pin.(当然你可以任意选择脚位） //3， PORTB----->数码管的段输出 //4， RD4，RD5，RC6，RC7------->数码管的位输出(数码管为共阴极） -///*******************// A description of the procedures:// 1, 24LC02 device address is 1010000R/W.// 2, write an array to take 24LC02 page write mode.// 3, the array read out the code from the 24LC02 to take a free read.// 4, using 4.00M crystal.// 5, using software I2C.// Second, the hardware to connect:// 1, SDA-------> 23 pin. (Of course, you can choose to pin)// 2, SCL-------> 18 Pin. (Of course You can choose pin)// 3, PORTB-----> digital tube output segment// 4, RD4, RD5, RC6, RC7-------> digital pipe-bit output (digital tube for a total of cathode)

采用AYG-59C GSM MODEM模块，和at89s52的串行口通信。通过at指令控制GSM模块，同时用单片机处理GSM发给单片机串口的反馈信息，实现远程无线控制。-Used AYG-59C GSM MODEM modules, and AT89S52 serial port communications. GSM through at command control module, at the same time deal with single-chip GSM distributed feedback single-chip serial port, wireless remote control.

MF500非接触式IC卡开发板源程序 -MF500非接触式IC卡开发板源程序

mage8的数码管扫描程序 -mage8 digital control digital control mage8 scanner scanner

是基于c8051f040单片机开发的电机转速测试程序。-SCM is based on c8051f040 test procedures developed by the motor speed.

八段数码管显示实验（Keil），这在德国的单片机软件上可以运行。-It shows experiment (Keil digital tube), which in German single-chip microcomputer software can run.