rs纠错编码－编码部分

在lpc1758上面进行lwip的不加系统的移植，实现tcp和uart的相互传输，可以从pc的网络终端写入数据传输到uart 然后在pc的串口终端显示，也可以从pc的串口终端写入数据，然后在pc的网络终端显示

linux下的vi编辑工具的所有快捷键用法，指法图，对学习vi的朋友有很大帮助-linux under vi editing tools all use shortcut keys, fingering chart, learning vi friends are very helpful

WindowsCE上的一个画板程序-WindowsCE a slate of procedures

读取温度的 msp430 单片机 ADC 的帮助。仪器： MSP 430 发射台软件： IAR 嵌入式的工作台。一份样品进行内部 1.5 v A10with 参考 Vref。软件设置 ADC10SC 开始样品 andconversion-ADC10SC 会自动清除在平等机会委员会。ADC10 内部振荡器/4 次样本 (64 x) 和转换。在主循环中 MSP430 等待 LPM0 保存 poweruntil ADC10 转换完成，ADC10_ISR 将迫使 reti 从任何 LPMx 通过循环退出。温度在摄氏存储在 IntDegC，华氏 inIntDegF。非标定温度测量从一个设备到另一个设备，将 varywith 边坡和偏移量-请参阅数据表。ACLK = n/a，是板上 = SMCLK = 默认 DCO ~1.2MHz，ADC10CLK = ADC10OSC/4

The objective is to set up SPI communication between VTI Technologies digital pressure sensor component and an MCU of an application device ATMEGA16L. In this code example: ?The MCU is configured ?SCP1000-D01 is initialized and configured ?The high resolution measurement mode is activated ?Temperature and pressure information is read always when the DRDY pin is in high state Please refer to the document "SCP1000 Product Family Specification 8260800" for further information on SCP1000 register addressing and SPI communication. This document applies to the SCP1000-D01.-The objective is to set up SPI communication between VTI Technologies digital pressure sensor component and an MCU of an application device ATMEGA16L. In this code example: ?The MCU is configured ?SCP1000-D01 is initialized and configured ?The high resolution measurement mode is activated ?Temperature and pressure information is read always when the DRDY pin is in high state Please refer to the

svsssvttttttttttttttttttttttttttttttttttttvffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDVVVVVVVVVVVVVVVVVV

stm32,单片机，电机控制程序，直流无刷电机，不包括PID控制

freescale的16位S12系列芯片MC9S12XEP100的Flash操作，包括系统时钟配置，FLASH初始化、擦除、写入。代码完整，有注释，组织良好，可以直接使用。

ARM9200+嵌入式linux下I/O程序-ARM9200+ Embedded linux under the I/O procedures

STM32F4移植ucOS-ii工程文件。特点：1、尽量不改变STM32F4的库文件，尤其启动文件startup_stm32f4xx.s；2、移植系统所需改动是在工程文件的uCOS/Port文件夹；3、新建两个任务进行测试；4、硬件平台为ST的STM32F4-DISCOVERY评估板