关于收音功能代码,并且显示在OSD和VFD上

一种基于高速逻辑器件（触发器，计数器和门电路等）控制的，可与各种单片机系统友好连接的高速A/D转换采集系统。-Based on high-speed logic device (flip-flops, counters and gates, etc.) control can be friendly with a variety of single-chip microcomputer system to connect high-speed A/D conversion acquisition system.

八段数码管显示实验（Keil），这在德国的单片机软件上可以运行。-It shows experiment (Keil digital tube), which in German single-chip microcomputer software can run.

51上的贪吃蛇程序，十分好，大家学习学习吧-51 on the Snake procedure is very good, everyone will learn it

51单片机C程序,学习单片机原理、硬件结构、扩展接口和编程语言。-51 Single-chip C procedures, learning Singlechip principle, the hardware structure, the expansion interface and programming languages.

DS18B20原理图及资料 -DS18B20 schematics and information

ARMMP3 ARMMP3 ARMMP3-ARMMP3 ARMMP3 ARMMP3 ARMMP3

急救车与交通灯）（1）南北与东西方向，每个方面由红黄绿三个灯控制（2）南北向：　红（30秒），黄（5秒），绿（25秒）　　　东西向： 红（35秒），黄（5秒），绿（25秒）　　　上述基本参数可以根据实际情况自行调整，灯的变化规律与实际路口规律相同，绿灯在最后5秒钟时，黄灯亮，然后红灯亮，不允许两个方面同时亮绿灯。（3）绿灯的时间显示在数码管上进行显示。（4）可以通过一个开关控制，当开关信号为0时，整个交通灯全灭提高要求：（1）设计一个紧急控制开关信号，当紧急开关信号为1时，两个方向的灯全为红灯。紧急开关撤消后，按照开关按下之前的状态继续运行（其参数要保存）。（2）设计一个夜间行车开关，当开关按下后，两个方向都只有黄灯闪烁，其它灯熄灭。（3）设计两个方向的亮时时间可调。-emergency vehicles and traffic lights) (1) North and South and east-west direction, each with three yellow-green from red lights control (2) to the north and south : red (30 seconds), yellow (5 seconds), Green (25 seconds) to things : red (35 seconds), yellow (5 seconds) Green (25 seconds) above basic parameters can be adjusted to the actual situation, the light changes with the actual law of the same intersection, the green light in the final five seconds, the yellow light is on, and then a red light, bright, not two fronts simultaneously bright green. (3) the green light at the time displayed on the digital display control. (4) can be controlled by a

通过C语言控制数码管动态扫描显示，通过按钮可以控制数码管的大小，然后进行定时器中断进行倒计时。-Through the C language to control the digital control of dynamic scan showed that the adoption of digital control button can control the size, and then proceed to the countdown timer interrupt.

一个用单片机控制饲服电机的程序，采用ＯＭＲＯＮ光纤感应器实现的剪纸机，已通过调试-By feeding a single-chip microcomputer to control the electrical service procedures, the use of fiber-optic sensor OMRON realize the paper-cutting machines, has passed through debugging

带中断输出功能的时钟芯片例程序,可移值，编译！-With interruption of the clock chip output function Example procedures, can shift the value, the compiler!