best 8051 anti

单一灯的左移右移分别接在单片机的P1.0－P1.7接口上，输出“0”时，发光二极管亮，开始时P1.0→P1.1→P1.2→P1.3→┅→P1.7→P1.6→┅→P1.0亮，重复循环-A single light, respectively, shifted to right then left at P1.0-P1.7 microcontroller interface, the output " 0" when the bright light-emitting diode, the beginning of P1.0 → P1.1 → P1.2 → P1. 3 → ┅ → P1.7 → P1.6 → ┅ → P1.0 Liang, repeat cycle

用AVR芯片，控制12864 LCD ，程序含有，ATMEGA8535驱动KS0108的12864，并含有温度测试程序-AVR chips used to control the 12864 LCD, containing procedures, ATMEGA8535 the KS0108 driver 12864 and contains the temperature test procedure

本设计以P89V51RD2FN单片机为电动小车的控制核心，采用MSA-LD2.0倾角传感器实时测量跷跷板的倾斜角，用ST198光电传感器检测黑色引导线监测小车运动。光电传感器和倾角传感器模块把实时测量信号馈送至单片机，利用专用细分芯片TA8435H驱动步进电机，以脉宽调制式斩波方式对步进电机步进角进行细分，控制和调节小车速度。采用增量式PID控制算法确保小车能够达到平衡；用RT128×64M液晶显示时间、角度等参数。经测试表明：小车各项性能指标达到设计要求，能够实现30秒内小车行驶到规定点，并保持跷跷板平衡；在跷跷板一端配重可调整的情况下，小车也能自动找到平衡点并保持跷跷板平衡。-The single-chip design for the electric car P89V51RD2FN control of the core, the MSA-LD2.0 seesaw angle sensor real-time measurement of the tilt angle, the detection of black ST198 photoelectric sensor to monitor vehicle movement and guide lines.Photoelectric sensors and angle sensors in real-time measurement module to feed the signal to the microcontroller, using a dedicated sub-chip stepper motor driver TA8435H to PWM chopper-type stepper motor on the sub-stepping angle, control and regulation vehicle speed. The use of incremental PID control algorithm to ensure that the car can achieve balance with LCD RT128 × 64M time, angle and other parameters.After the test showed that: the performance car

这是一个基于8051单片机的用c语言写的一个时钟程序，个人原创哦-This is a 8051 based on the use of c language program written in one clock, personal original Oh

一个12864液晶显示的程序，希望对大家有点用，希望有液晶开发经验的朋友来交流-a 12,864 LCD procedures, we hope to use a bit, LCD hope that the development experience of a friend to share

使用1520控制器的12232点阵液晶模块的51单片机控制C代码,keil编译通过,使用端口直接连接方法,P1口为数据口,控制线在P3部分端口-1520 controller using dot matrix LCD module 12232 51 C MCU control code keil compiled by the use of ports directly connected, I P1 for data export, the line of control in some ports P3

自制的一个单片机发送按键代码,另一个单片机接收按键代码的实例.-adfadf adf asdf asd fasd fadf sdfasdf asdf sadfsadf asdf asdf d fadf sadfasdf asdfa

基于凌阳和ad9850实现的正弦波信号发生器程序，包含键盘、显示模块程序-Sunplus and the AD9850 based on the realization of the sine wave signal generator procedures, including keyboard, display module procedures

51单片机三首歌播放原代码-51 Singlechip three songs to play the original code

DEW POINT CALCULATION ROUTINE