用keil环境和proteus实现的16*16四字点阵显示

这是一款烘手机应用程序，有高中低三个档，用数码管显示-This is a mobile application bake, and three low-profile high school, with digital display

程序下载在M16中后，以后不需要任何编程器，只需连接串口就可以使用STK500专业编程器的功能 -Download of the M16, after does not require any programming, simply connect serial port on the STK500 can use the functions of professional programmer

本系统利用凌阳SPCE061A单片机原理，设计了一种双向超声测距系统，与一般的超声测距系统相比，除具备一般测距系统具有的功能外，该系统还具有低功耗、高精度、工作可靠、人机交互界面友好等优点。由于超声传播速度与环境温度相关而采用声速温度自动补偿技术，根据测量不同距离和不同的反射材料，回波信号强度从几毫伏到几百毫伏变动，因而采用两片AD603组成AGC自动增益控制电路与低噪放大器 NE5532 级联使用的方式组成超声检测信号放大电路，提高超声检测系统的检测范围和系统的适应性，使的系统获的较好的整机性能。由于超声波的传播距离与它的振幅成正比，为了使测距范围足够远，可对单片机输出方波信号进行功率放大后再加在超声波换能器上，因而先由三极管8050进行功率放大，再通过由六非门CD4049接成推挽方式的驱动电路将振荡信号的幅度放大一倍，再接到超声波换能器，从而增加了超声波的传播距离，扩大了测距范围。-err

* 硬件结构： PA0-5对应６个ＬＥＤ数显管的位 ，PC0-7对应各ＬＥＤ数显管的段 ，PB4-7为键盘。 * 软件描述： 上电后，时钟从00.00.00（时/分/秒）自动走时，在走时状态时 ， 按PB4（设定 * 键）超过3秒可循环选择调整时间/工作参数 ，接着按PB5以确定选择的操作 ，进入调整操作后 ， * 按PB5选择欲调整参数，按PB6（增加键）完成调整参数操作 。按PB7，进入时控运行，PB1亮， * 再按PB7停止时控运行，回显走时。在定时到时，PB0点亮。- * Hardware architecture: PA0-5 corresponds 6 LED numbers to reveal the tube the position, PC0-7 corresponds each LED number to reveal the tube the section, PB4-7 is a keyboard. * Software description: After on electricity, clock from 00.00.00 (when/a minute/second) is in luck automatically, when is in luck the condition, according to PB4 (hypothesis * The key) surpasses for 3 seconds to be possible to circulate the choice time/operational parameter, then presses PB5 by to determine the choice the operation, after enters the adjustment operation * Wants according to the PB5 choice to adjust the parameter, (increases key) according to PB6 to complete the adjustment parameter operation.According to PB7, enters when controls the mov

winbond的w77e58双串口测试-the dual serial test

用中断的方式控制lcd的显示，单片机仍然是h83664十六位单片机。此程序包含单片机的接口的配置以及各种写lcd的子程，使用中断来控制lcd顺序显示A－Z，当然，可以换成其他的显示内容，由于接口程序已经编好，只需要把要显示的内容改一下就可以实现其他内容的显示-With interruption control lcd display, single-chip is still 16 Singlechip h83664. This procedure includes the configuration of single-chip interface and a variety of writing a sub-lcd-way, the use of interrupt to control the order in lcd display A-Z, of course, can be replaced by other display content, as a result of interface procedures have been developed only to To display the contents of change can be achieved about the display of other content

利用实验板上的89C51,8279,LED,LCD等资源设计篮球比赛记时记分器，要求能够显示当前比赛时间和双方比分、剩余时间、24秒倒计时-The use of experimental board 89C51, 8279, LED, LCD and other resources designed basketball game when the scoreboard in mind, and asked to display the current game time and both scores, the remaining time, 24 seconds countdown

用于参考msp430f149硬件连接图，个个引脚的分配，可以做下载-MSP430F149 for reference hardware connection diagram, the distribution of each pin, you can download to do

讲述了单片机要求的对齐原理 对结构体的理解非常重要-Tells the MCU requirements of the body alignment principles of the structure is very important to

LT_1B msp430开发板例子程序－HFXT