手机端与电脑实现串口通信，在VC环境下编程，包含源程序

串口通信的事例FPGA上面可以实现非常实用-FPGA serial communication above examples can be very useful for implementation

Mobile phone UART 2 MMC card read example

spcomm是DELPHI，BCB下的，非常好用的VCL控件，比MSCOM好用些。这个源程序给出了spcomm的基本用法。-spcomm is Delphi, the BCB, very handy VCL controls more than EMS handy. This is a source spcomm the basic usage.

Delphi是一种具有功能强大、简便易用和代码执行速度快等优点的可视化快速应用开发工具，它在构架企业信息系统方面发挥着越来越重要的作用，许多程序员愿意选择 Delphi作为开发工具编制各种应用程序。但是，美中不足之处是 Delphi没有自带的串口通信控件，在它的帮助文档里也没有提及串口通信，这就给编制通信程序的开发人员带来许多不便-with Delphi is a powerful, easy-to-use and faster code execution advantages of visual rapid application development tool, the framework for enterprise information systems are playing an increasingly important role, many programmers choose to Delphi as a development tool preparation of the various applications. However, inadequate as it is not Delphi onboard Serial Communication Control, in its help files contain no mention of serial communication, which gives the procedures for the preparation of communications developers bring a lot of inconvenience

本串行通信程序利用汇编语言通过BIOS中断调用和DOS功能调用实现PC机双机串行通信。其中，上位机和下位机串行口均为辅串口COM2（口地址为2FXH），对外用9针连接器与令一台PC机连接；BIOS通过“INT 14H”4个中断服务子程序，分别完成串口初始化编程、发送一帧数据、接受一帧数据以及测试通信线状态。本程序分为PC机串口自动测试程序（目的是测试串口好坏）和PC机全双工双机通信程序两个部分。-the serial communications procedures through the use of assembly language BIOS interrupt calls and function calls DOS PC Dual Serial Communication. Among them, PC and the next crew will be supplemented by serial port Serial COM2 (I address 2FXH) external with 9-pin connectors and enable a PC connection; through the BIOS "INT 14H," four interrupt service routines, complete serial port initialization programming, Send a data receiving a data communications test and the state line. The procedures are divided into PC serial automatic test procedure (for the purpose of testing Serial good or bad) and full-duplex PC-machine communication program two parts.

本代码是VC源代码，实现通过串口接收和发送短消息。-VC code is the source code to achieve through the serial port to receive and send short message.

本程序是i2c总线读写一个字节的程序。在写过程序中，不一定非要检测i2c的应答位，可以直接延时过去就行，但是在读过程中必须给应答信号，读完发停止位，一定确认所发的信号都发上了。否则在连续地址读的过程中可能不会出错，但是在随机度过程中就会出错，我的程序就是在给停止信号时没有给上，24cxx一直在输出数据，结果读出错。找着问题后我的程序只加入了一条命令便完全正常。-i2c bus read and write a byte procedures. The written procedure, not necessarily require the detection i2c-response, and can directly past trip delay, but the process must be read to the response signal, stopped at reading, we recognize the signals are on the fat. Otherwise, the address read for the course could not go wrong, but the randomness of the process would be a mistake, I was in the process to stop for no signal, 24cxx in output data, read errors. I discovered the problem after the procedure just joined the order of a completely normal.

一个串口通信的例子，选取接口，然后可以接受和发送数据。-A serial communication example, select the interface, and then can receive and send data.

是一个串口通信的程序,本人前段时间做的一个项目.-is a serial communication procedure, I do a side project.

利用新型单片机c8051f020进行的编程，该单片片机具有很高的性价比。-new SCM C8051f020 use the program, the single pieces of the machine has a price.