EasyARM2131 one source development board

周立功提供的基于菲利普ARM的LPC2200微控制器的图形库源程序-based Philips LPC2200 ARM Microcontrollers the graphics library source

sharp arm7 bootloader code

ARM7202上通过JTAG烧录Flash的工具源代码，内有说明文档

杭州利宇泰公司的基于44B0的ARMSys开发板上的大量源代码，包括ADC、ARP、彩色LCD、外部中断、以太网底层函数、FAT16文件系统、Flash ROM、GUI软件包、Helloworld程序、IIC接口、扫描键盘、Ping程序、44B0内置RTC示例、SDRAM接口、定时器示例、触摸屏示例、UART示例和uC/OS-II的移植、应用（包括多任务、任务间通信、中断服务程序）、UDP数据传输、USB固件编写等程序代码和工程。一次性共享给大家使用。可以作为其他samsung44B0开发板上应用程序的下载。-Lee Yu-tai Hangzhou-based company 44B0 ARMSys development board of a large number of source code, including the ADC, ARP, color LCD, external interrupts, Ethernet bottom function, FAT16 file system, Flash ROM, GUI packages, Helloworld procedures, IIC interfaces, scanning keyboard, Ping procedures 44B0 built-in RTC example, SDRAM interface, timers example, the touch screen example, UART examples and uC/OS-II transplants, applications (including multitasking, inter-task communication, interrupt service routine), the UDP data transmission, USB firmware preparation procedures code and engineering. One-time use for everyone to share. As other samsung44B0 development board application downloads.

本程序,利用51单片机AT89C51来读写多功能芯片X5045的源程序-This procedure, using 51 to read and write AT89C51 single-chip multi-chip source X5045

S3C44B0X通过ADS7846驱动触摸屏程序-S3C44B0X through the ADS7846 touch screen driver program

ucosii,if you cant to study os,please contwact me.-ucosii, if you cannot to study os. please contwact me.

开发环境:ADS 1.2/SDT 2.51 GUI测试，由于没有触摸屏，所以将触摸屏的代码给屏蔽了； 请将FS44B0II开发板连接好交叉网线、直连串口线、电源， 并连接好G57液晶屏，同时还要连接好背光电源； 然后在BIOS的命令窗口里面敲netrun命令； 点击FS44B0_G57_uCGUIuC-GUIFS44B0_G57_uCGUI_DataDebugRel目录下： 批处理文件FS44B0_G57_uCGUI.BAT 下面你就可以看到液晶屏上面显示优龙标志 它会延时一两秒中进入下一个画面，逐步延时GUI的各项功能，请耐心观看； -Development Environment: ADS 1.2/SDT 2.51GUI test, because there is no touch screen, it will be touch screen to shield the code Please FS44B0II development board to connect a good cross-network lines, direct serial lines, power supply, and connect a good G57 LCD screen, at the same time, good backlight power supply connection and then in the BIOS command window knock netrun order Click FS44B0_G57_uCGUIuC-GUIFS44B0_G57_uCGUI_DataDebugRel directory: batch file FS44B0_G57_uCGUI.BAT below you can see the LCD screen above shows excellent signs that it will delay Liuzhou 1 two seconds to enter the next screen, and gradually delay the GUI features, please be patient watch

关于ADS7843的英文文档，，要求英文水平好，，要不搞不定-on ADS7843 English document, require a good standard of English, either forum

NiosII串口命令解析串口部分，包括中断，发送命令提示符，接收字符处理等。耗费了不少心血的！对初学者绝对有用。-Command Parsing NiosII serial serial parts, including the interruption, send the command prompt, receiving treatment and other characters. Spent a lot of hard work! Definitely useful for beginners.