MiniWeb 在嵌入式平台上运行的WEB源代码

串行口输入，只使用三根线，对于学习TLC0831的同学会有点帮助。-Serial port input, using only three lines, for the students to learn TLC0831 will to some extent.

4x4的键盘的程序在430单片机程序，键盘是有源的，硬件电路设置成的是上拉-4x4 keyboard program in 430 MCU program, the keyboard is active, the hardware circuit set the pull-up

嵌入式系统课件:嵌入式系统基础,嵌入式系统设计开发流程等共12章内容-Embedded systems software: the basis for embedded systems, embedded systems design and development processes, such as Chapter 12

很多verilog源代码，包括很多小电路。

摘要：该声音导引系统由声音导引主控系统和小车控制系统两部分组成。声音导引主控系统主要由主控MCU、声音接收部分、无线发射模块组成。小车控制系统主要由MCU、固化模块NEC、电机驱动部分、声光部分及无线接收模块组成。该系统的最大特点在于其软件设计使用层次化、模块化设计方法，系统低功耗，性价比低。经调试和测试，系统各项性能参数达到设计指标。 关键词：声音导引、无线收发、声源移动、M 智能语音小车-Abstract: The guidance system consists of the sound systems and car audio guidance master control system composed of two parts. Sound-guided mainly by the main control system master MCU, the sound receiving part, the wireless transmitter module component. Vehicle control system mainly consists of MCU, curing module NEC, motor drive parts, sound and light parts and the wireless receiver module. The most prominent feature of the system software designed for use in its hierarchical, modular design approach, the system low-power, low cost. The debugging and testing, system performance parameters to achieve the design target. Key words: sound guidance, wireless transceiver, a sound source movement, MCU, NEC, motor drive

介绍一种基于摄像头的智能车自动控制器设计方案。以飞思卡尔16 位单片机为核心控制单元，使用红外光电传感器采集路径信息，控制智能车的舵机、驱动电机，实现智能车的自主寻迹行驶。 -Introduction of a camera-based automatic control of intelligent vehicle design. Based on Freescale 16-bit microcontroller as the core control unit, the use of infrared photoelectric sensor acquisition path information, control, intelligent vehicle steering gear, drive motors, autonomous intelligent vehicles driving tracing.

The project demonstrates many Windows common controls, including the extensive use of image lists. The project was used in the book "The Revolutionary Guide To MFC 4 Programming With Visual C++", published by Wrox Press.

豪华板中E35G23的UCOS2+UcGUI图形系统2.76，UCOS_II测试程序说明，由hgxxx的ucosii2.71升级而来的！去掉了TaskLcd running显示，把这个任务作为GUI显示输出，类似于UCOS的例子1，在一个随机的位置显示一个随机数，只是允许一个任务调用GUI，没有显示cpu利用率、切换次数等信息！注意：~本程序适用于240×320 16级灰度液晶！去掉了TaskLcd running显示，把这个任务作为GUI显示输出，类似于UCOS的例子1， -luxury plate E35G23 the UCOS2 2.76 UcGUI graphics system, UCOS_II test procedures provided by the ucosii2.71 escalation hgxxx come! TaskLcd removed from the running has shown that this task as shown GUI output UCOS examples similar to the one in a random location of a random number, allow only one task calling GUI, no indication of cpu utilization, switching frequency information! Note : ~ procedures applicable to the 240 x 320 16-greyscale LCD! TaskLcd removed from the running has shown that this task as shown GUI output UCOS similar to the one example,

开发环境：Eclipse+yagarto+openocd+st-link STM32Fxxx+MPU-6000+MS5611(BMP085)+HMC5883 AHRS算法：方向余弦矩阵

这是一个简单的 C 程序，在 C 中的液晶显示为 8051 的设计说明中给出细节和容易理解