-
MATLABJIECHENG
matlab学习资料,讲述了在matlab下如何计算阶乘。(matlab learning materials, about how to calculate the factorial in matlab.)
- 2013-10-22 16:28:38下载
- 积分:1
-
51 Labview
说明: 使用单片机控制电机,在labview界面上调节相关的控制参数,在labview界面上观测各个控制的参数变量。(The single chip microcomputer is used to control the motor, the relevant control parameters are adjusted on the LabVIEW interface, and the parameter variables of each control are observed on the LabVIEW interface.)
- 2020-03-06 11:12:09下载
- 积分:1
-
虚拟仪器高级应用
虚拟仪器高级应用全书例子,用的C语言开发环境Labwindows/CVI,有各种高级应用的例子,非常值得学习参考。(Virtual instrument advanced application book example, using the C language development environment Labwindows/CVI, there are a variety of advanced application examples, it is worth learning reference.)
- 2017-11-06 21:00:00下载
- 积分:1
-
Joint-time-frequency-analysis
基于labview的chirp信号联合时频分析,2012版本以上(Joint time-frequency analysis of chirp signal based on labview)
- 2021-03-13 09:29:25下载
- 积分:1
-
Labview-shili
实例:设计双通道数据采集回放系统,首先实现基本波形模拟发生、数据采集记录;其次对记录数据进行回放、分析处理。(Example: Design of two-channel playback system of data collection, the first place to achieve the basic waveform simulation, data acquisition records followed by playback of recorded data, analysis and processing.)
- 2020-07-15 17:38:50下载
- 积分:1
-
shijian-3
数据实时采集,实现数据的动态记录,比如平均周期,峰峰值等(Real time data acquisition, dynamic recording of data, such as the average cycle, peak value, etc.)
- 2017-04-07 18:18:02下载
- 积分:1
-
SubVIs
模拟FM信号的解调子程序,包括下变频、A/D采样、正交解调,最后输出基带信号。(Subroutine analog FM demodulation signal, comprising down-conversion, A/D sampling, orthogonal demodulation, and finally outputs a baseband signal.)
- 2013-11-26 16:23:32下载
- 积分:1
-
signal_001
信号发生器,带扫频,带频率的切换!最小可以0.1HZ。(Frequency sweep signal generator, belt, belt frequency switch! Minimum to 0.1 HZ.)
- 2013-06-30 09:03:01下载
- 积分:1
-
LABVIEW3D显示
该程序是基于LABVIEW软件编程的程序,是用于3维图形显示用的,三维图形绕轴旋转,
该程序是基于LABVIEW软件编程的程序,是用于3维图形显示用的,三维图形绕轴旋转,
该程序是基于LABVIEW软件编程的程序,是用于3维图形显示用的,三维图形绕轴旋转,
该程序是基于LABVIEW软件编程的程序,是用于3维图形显示用的,三维图形绕轴旋转,
该程序是基于LABVIEW软件编程的程序,是用于3维图形显示用的,三维图形绕轴旋转,
该程序是基于LABVIEW软件编程的程序,是用于3维图形显示用的,三维图形绕轴旋转,
- 2022-04-10 20:03:35下载
- 积分:1
-
UART
Labview串口指令收发,测试可用,放心下载(Labview YART)
- 2016-01-04 14:44:15下载
- 积分:1