用于步进电机的驱动.可以通过输出信号来控制步进电机的转速和角度控制....

在点阵式液晶显示器上显示字符-in dot-matrix liquid crystal display characters on the show

反汇编 Ver1.2-anti-compilation Ver1.2

本程序用于MICROCHIP 24LC64 EEPROM的读写。本程序不使用芯片级联方式， 请将A0，A1，A2 管脚接至低电平。本程序使用IOC6作为SDA，IOC7作为SCL。 程序中的地址空间最大可至64K：24LC00-16-0，24LC01-128-8，24LC02-256-8， 24LC04-512-16，24LC08-1K-16，24LC16-2K-32，24LC32-4K-32，24LC64-8K-32， 24LC128-16K-64，24LC256-32K-64，24LC512-64K-128，读写数据均为8bits。 以上器件的格式为（型号-地址空间-页大小）不同器件的页大小不同，因此页写 程序需作相应修改，其他字节写，随机读以及顺序读程序均相同-This procedure for the MICROCHIP 24LC64 EEPROM read and write. This procedure does not use chips cascade way, please A0, A1, A2 pin to low level access. This procedure used IOC6 as SDA, IOC7 as SCL. Process address space available to the largest 64K: 24LC00-16-0, 24LC01-128-8, 24LC02-256-8, 24LC04-512-16, 24LC08-1K-16, 24LC16-2K-32, 24LC32-4K- 32,24 LC64-8K-32, 24LC128-16K-64, 24LC256-32K-64, 24LC512-64K-128, read and write data are 8bits. The format for the above device (Model- address space- page size) of different devices of different sizes of pages, so page written procedures need to be amended accordingly, and other bytes to write, rand

VGA视频切换矩阵源玛,采用PIC单片机16F628实现8*8的视频切换.-VGA Video Switch Matrix Mary source using PIC 16F628 to achieve 8* 8 video switching.

　C8051F330/1 MCU 有一个可编程内部高频振荡器、一个可编程内部低频振荡器和一个外部振荡器驱动电路。可以通过对 OSCICN 和 OSCICL 寄存器编程来使能/禁止内部高频振荡器和调节其输出频率（参看振荡器框图）；可以通过对 OSCLCN 寄存器编程来使能/禁止内部低频振荡器和调节其输出频率（参看图9.3）。系统时钟可以由外部振荡器电路或任何一个内部振荡器提供。表9.1给出了内部振荡器的电气特性。 -C8051F330/1 MCU has a programmable internal high-frequency oscillator, a programmable internal low frequency oscillator and an external oscillator drive circuit. Can register on OSCICN and OSCICL programming to enable/disable the internal high-frequency oscillator and adjust its output frequency (see diagram oscillator) OSCLCN can register through the programming to enable/disable the internal low frequency oscillator and adjust its output frequency (see Figure 9.3). System clock can be external oscillator circuit, or any provision of an internal oscillator. Table 9.1 gives the electrical characteristics of the internal oscillator.

FREESCALE MCF52XX eTPU控制三相电机的程序-eTPU CODE

8051系列单片机C程序设计完全手册和一些简单的c程序-8051 Series Single-chip C programming manual and complete some simple c program

C语言写的日历时间程序。采用51单片机。-C language writes calendar time sequencing. Uses 51 monolithic integrated circuits.

一个简单的VB界面程序,包括按钮,文本等,此程序是一个CanOpen通讯的上位机界面,通过提供的接口函数,进行数据的接收和发送.希望对学习VB的有所帮助.-A simple VB interface procedures, including buttons, text, etc., this program is a PC CANOpen communication interface, by providing the interface function, to receive and transmit data. I hope to learn from the VB help.

Easy 51Pro串行编程器,这是下位程序用(Keil C)编译后烧入单片机.-Easy 51Pro serial programmer, This is the next procedure used (Keil C) compiled burned into SCM.