lcd 驱动

说明：  51单片机控制GSM模块发短信和打电话的C源码(GSM single-chip control module 51 send text messages and phone calls the C source)

在淘宝上购买的毕业论文，价值400的源程序，包含全部文件。一款基于单片机的灭火机器人模型的设计。系统以STC89C52RC单片机为控制核心，创新自制了火焰传感器用来测量火源，使用TCRT5000型光电对管检测循迹黑线，L298驱动电机前后转动，LCD1602液晶显示灭火的次数，通过控制继电器开关风扇灭火。(On Taobao buy thesis, the value of the 400 source code, including all documents. Fire fighting robot model based on a single-chip design. System microcontroller STC89C52RC to control core, innovation homemade flame sensor is used to measure the fire source, tracking black line on the tube use TCRT5000 photoelectric detection, L298 drive motor rotating back and forth, the LCD1602 LCD number of fire-fighting, fire control relay switch fan .)

0－1背包Backtrack,算法中回索法的一个好例子(0-1 Knapsack Backtrack, back Sofa algorithm a good example of)

说明：  AD7799 AD转换芯片，电压采集驱动程序。(AD7799 AD conversion chip, voltage acquisition driver.)

这是完整的五子棋MATLAB源码，绝对能运行，能走五子棋。(this is a complete connective_five matlab code )

C#版snmp网络管理软件，具备网络编程源码，SNMP源码(C# version of SNMP network management software, network programming source code, SNMP source code )

这是一个利用dsp的gpio口实现不同的功能模块和数字口功能，程序完整可运行(This is a use of the GPIO DSP port to achieve different functions and functions of the function module, the program can run )

使用STM32F103单片机DSP库函数编写的FFT1024点快速傅里叶变换，数据来源是ADC数据采集，通过串口打印输出变换后的结果。(Use STM32F103 microcontroller DSP library functions written FFT1024 point fast Fourier transform, data source is the ADC data capture, results through the serial port printout after conversion.)

利用STC12系列单片机实现对WS2812B的控制  程序包含了WS2812B的驱动和灯光逻辑控制的代码  包括任意点亮任意颜色的LED、流水、跳跃、渐变、对冲等

牛顿－拉夫逊法潮流计算 基本步骤： 　　（1）形成节点导纳矩阵 　　（2）将各节点电压设初值U， 　　（3）将节点初值代入相关求式，求出修正方程式的常数项向量 　　（4）将节点电压初值代入求式，求出雅可比矩阵元素 　　（5）求解修正方程，求修正向量 　　（6）求取节点电压的新值 　　（7）检查是否收敛，如不收敛，则以各节点电压的新值作为初值自第3步重新开始进行狭义次迭代，否则转入下一步 　　（8）计算支路功率分布，PV节点无功功率和平衡节点柱入功率。(Newton-Raphson method flow calculation basic steps : (1) formation of nodal admittance matrix (2) to set up the initial node voltage U, (3) the initial node-generation-related demand. calculated that the constant term formula Vector (4) nodes will be incorporated into the initial voltage-seeking, calculated Jacobian matrix elements (5) solving that equation, seek to amend the vector (6) to strike a new node voltage value (7) to check whether convergence, if not restrained. concentrated in the nodes of the new voltage as the initial value since the first three steps to re-start the narrow iterations. Otherwise, turn into the next (8) Calculation branch power distribution, PV nodes reactive power and balance-node into power.)