编译环境为ADS, 用于proteus仿真，基于ARM7芯片

基于凌阳单片机的多功能水温自动控制系统的硬件设计。-Sunplus based on single-chip multi-functional water temperature automatic control system hardware design.

51单片机驱动青云创新的LCM3202403的源码，采用控制器方式，控制器为S1D137-51 single-chip driver LCM3202403 Albatron source of innovation, using the controller mode, the controller for the S1D13700

单片机P1口与4个按键连接，用于信号幅度和频率调节操作键。单片机P0、P2.7、P3.6(-WR)与DA0832、2个741(运放)连接构成波形信号输出电路。 编程使波形信号输出电路输出正弦波信号，并且可通过操作键调节信号的幅度和频率。幅度和频率调节级别从0~10，共11个等级。 -Singlechip P1 I connect with the four buttons for the signal amplitude and frequency adjustment operation keys. Singlechip P0, P2.7, P3.6 (-WR) and DA0832, 2 months 741 (operational amplifier) to connect constitute waveform signal output circuit. Programming so that waveform signal output circuit output sine wave signal, and can be operated keys adjust the signal amplitude and frequency. Amplitude and frequency adjustment level from 0 ~ 10, a total of 11 grades.

c c++语言编程 的仪表放大器原理分析 - 模数电路 - 新势力论坛 单片机,嵌入式,51,ARM,AVR,工控,自动化-C c++program Featuring high performance and versatility

51单片机方面的程序 用汇编写的 很经典的一些程序-51 SCM procedures used to write the classic compilation of some of the procedures

温度芯片功能的读写程序，包括汇编原代码，可烧录文件，熟悉一线产品的读写方式-Function of the temperature reading and writing chip procedures, including the compilation of the original code, recordable document, the reader familiar with the product line approach

18b20的程序，可以用的，avr mega8-18b20 procedures can be used, avr mega8

51系列单片机实验课程：串口 （通过计算机与试验箱相连，互相收发信息）-51 Series single-chip experimental curriculum: serial (through the computer and the chamber connected to each other to send and receive information)

本设计以P89V51RD2FN单片机为电动小车的控制核心，采用MSA-LD2.0倾角传感器实时测量跷跷板的倾斜角，用ST198光电传感器检测黑色引导线监测小车运动。光电传感器和倾角传感器模块把实时测量信号馈送至单片机，利用专用细分芯片TA8435H驱动步进电机，以脉宽调制式斩波方式对步进电机步进角进行细分，控制和调节小车速度。采用增量式PID控制算法确保小车能够达到平衡；用RT128×64M液晶显示时间、角度等参数。经测试表明：小车各项性能指标达到设计要求，能够实现30秒内小车行驶到规定点，并保持跷跷板平衡；在跷跷板一端配重可调整的情况下，小车也能自动找到平衡点并保持跷跷板平衡。-The single-chip design for the electric car P89V51RD2FN control of the core, the MSA-LD2.0 seesaw angle sensor real-time measurement of the tilt angle, the detection of black ST198 photoelectric sensor to monitor vehicle movement and guide lines.Photoelectric sensors and angle sensors in real-time measurement module to feed the signal to the microcontroller, using a dedicated sub-chip stepper motor driver TA8435H to PWM chopper-type stepper motor on the sub-stepping angle, control and regulation vehicle speed. The use of incremental PID control algorithm to ensure that the car can achieve balance with LCD RT128 × 64M time, angle and other parameters.After the test showed that: the performance car

scan file in microstation, simple example