登录
首页 » 通信 » Visual Basic.NET 和闪光之间的通信

Visual Basic.NET 和闪光之间的通信

于 2022-06-29 发布 文件大小:76.38 kB
0 181
下载积分: 2 下载次数: 1

代码说明:

VB.NET 和闪光之间的通信。此示例将显示如何 flash 将发送该变量到 vb.net,反之亦然。.FLA 项目是包括在内的。

下载说明:请别用迅雷下载,失败请重下,重下不扣分!

发表评论

0 个回复

  • this a book that learning serial programming
    this a book that learning serial programming-this is a book that learning serial programming
    2022-05-10 14:51:51下载
    积分:1
  • VB serial monitoring program
    VB串口监视程序-VB serial monitoring program
    2023-07-28 20:05:04下载
    积分:1
  • 讲述最新的定位系统的号格式,BOC调制与解调技术的资料
    讲述最新的定位系统的信号格式,BOC调制与解调技术的资料-BOC modulator and demodulator
    2022-03-22 10:22:40下载
    积分:1
  • CMU200_RF_Test_src
    自己用VB6.0写的visa32控制CMU200测试手机射频指标工具,要安装visa32驱动。手机装测试白卡,自动拨号连接手机,自动生成测试报告。-Own use VB6.0 to write visa32 control CMU200 test mobile radio indicator tools, mobile equipment testing white card, automatic dial-up connection phone to automatically generate test reports.
    2022-06-28 03:11:36下载
    积分:1
  • 扩频序列的误码率性能仿真程序,在MATLAB环境下运行
    扩频序列的误码率性能仿真程序,在matlab下运行-Sequence Spread Spectrum BER performance simulation program, run under Matlab
    2022-02-04 01:34:55下载
    积分:1
  • 连接到数据
    connection to the CY7C68013A-56 ADC AD9203. Software and Firmware-connection to the CY7C68013A-56 ADC AD9203. Software and Firmware
    2022-02-24 18:56:06下载
    积分:1
  • vc modem代码
    vc modem通信代码-vc modem communications code
    2022-08-18 06:44:01下载
    积分:1
  • 计算机MC35接收软件
    计算机通信MC35接收软件-MC35 receiving computer communication software
    2023-02-17 21:25:03下载
    积分:1
  • 原版只能CPU卡标准ISO/IEC7816
    原版只能CPU卡标准ISO/IEC7816-4-Only original CPU card standard ISO/IEC7816-4
    2023-06-27 16:45:04下载
    积分:1
  • 0. Install the rp
    0. Install the rp-pppoe-software -------------------------------- You should have already done this by the time you re reading this. If not, go back and read README. 1. Set up your Ethernet hardware -------------------------------- First, make sure the Ethernet card you intend to use with the modem is visible to the Linux kernel. Just how to do this is beyond the scope of this document. However, if the card is the only Ethernet card in the system, executing: ifconfig eth0 should display something like this: eth0 Link encap:Ethernet HWaddr 00:60:67:62:31:D4 plust some more lines. Your HWaddr will be different. As long as you see the HWaddr line, your card should be working. DO NOT assign an IP address to the Ethernet card. DO NOT configure the card to come up at boot time.-0. Install the rp- PPPOE-software-------------------------------- You should have al ready done this by the time you re reading this. I f not, go back and rea
    2023-03-02 00:45:03下载
    积分:1
  • 696516资源总数
  • 106914会员总数
  • 0今日下载