这是一个用LPC2132作的终端，有通协议源代码和SED1335控制液晶源代码...

利用Winsock进行tcp连接的cs架构，包括服务器和客户的连接。 vc 6.0开发，通过建立基本的tcp链接进行数据通信，可以扩展应用做基本的通信。

1)生成2KHz和8KHz的混合信号，使该信号通过上述滤波器，观察滤波前后的波形变化和频谱分布情况。 2) 在改信号中加入高斯白噪声，观察滤波前后的波形变化和频谱分布情况3) 将上述滤波器改为中心频率为100KHz的带通滤波器，信号源为带外的90KHz和带内的100KHz的混合正弦信号，。 4) 用M文件实现上述低通滤波器。 -1) 2KHz and 8KHz to generate the mixed-signal, so that the signal through the above-mentioned filter, filter before and after observation of the waveform and spectrum distribution of the changes. 2) add to the signal in white Gaussian noise was observed before and after filtering and spectral waveform changes in the distribution of 3) will be replaced by the above-mentioned filter center frequency of 100KHz band pass filter, the signal source for the band and the band of 90KHz 100KHz Sine of the mixed signals. 4) achieve the above-mentioned documents with M low-pass filter.

点到点无线通信实验，属于无线传感器网络中基础通信类相关代码。-Point-to-point wireless communications experiment, wireless sensor networks belong to basic communications in the relevant category code.

朋友们，大家好！ 内存文件映射和进程间通讯演示程序-friends, everyone! Memory mapping document and inter-process communication Demonstration Program

Viterbi 译码 多的就不说了 我刚运行过可以的-Viterbi decoder and more I just can not say that I can run the

PPP Deflate压缩协议（PPP Deflate Protocol） 摘要 点到点协议（PPP）[1]提供了一种在点到点链路上传输多协议数据报的标准方法。压缩控制协议（CCP）[2]提供了一种在PPP封装链路上协商和使用压缩协议的方法。本文档描述了如何使用PPP Deflate压缩协议压缩PPP封装报文。 -PPP Deflate compression protocol (PPP Deflate Protocol) Abstract point-to-point protocol (PPP) [1] provides a point-to-point link, the multi-protocol data transmission of standard methods. Compression Control Protocol (CCP) [2] provides a link in the PPP Packaging consultations on the agreement and the use of compression method. This document describes how to use the PPP Deflate compression compression PPP agreement Packaging paper reported.

Microsoft SDP Extensions.

DNW的0.5源代码，支持USB和Serial的Download，在VC6.0下测试通过。-DNW 0.5 source code, support for USB and Serial for Download, in VC6.0 under test.

Visual C++ 串口通信编程实践 第9章和第10章源码 -Visual C++ Serial communication programming practice, Chapter 9 and Chapter 10 source code

接口模块，通过对高位地址的编码可实现在一个FPGA中配置四个独立的功能模块，每个功能模块具有一个带FIFO的输出口和13个独立的可由DSP读写的寄存器，寄存器功能可自定义。模块还包含两个全局寄存器，可实现全局复位，中断等功能。该模块以应用于实际的项目中，目前运行良好