键盘扫描程序 台湾义隆EMC汇编,程序后缀DT C0

中颖单片机sh6613的一个坐标扫描程序，其中有模拟串口通信等，值得一看！-SinoWealth Singlechip sh6613 coordinates of a scanning process, including simulation of serial communication and so on, worth a visit!

LCD12864源代码 NEC公式芯片 包括控制液晶显示屏的各个函数-LCD12864 formula for the source code NEC LCD chips including control various functions

这是一套用C语言完成的128*64液晶屏驱动，没有设备，未验证可用性-This is a set of C language with the completion of the 128* 64 LCD screen-driven, not equipment, not to verify the availability of

阀位控制器源程序 利用PIC16F873A-valve controller source use PIC16F873A

温度传感DB18B20七段显示实验

atmel89c51cc03单片机的can通信，调试通过-atmel89c51cc03 SCM can communication, debugging through

基于PIC16F877A的DS18B20一线总线多路测温系统（采用Proteus模拟）。 Proteus模拟电路图＋PIC C语言源程序（MPLAB V8.00） 这可不是用多I/O模拟的多路测温哦！看系统功能： 1）、由一线数据线寄生供电，采用MOSFET强上拉给DQ供电； 2）、上电自动搜索可用的传感器并做CRC校验（实现了Search ROM命令）； 3）、 报警下限可选择； 4）、轮询显示温度，通过LCD1602输出； 5）、 传感器中途拔出或温度越界均报警； 6）、 采用声光报警方式，可做为温度控制信号标志。 -PIC16F877A-based multi-channel bus of DS18B20 line temperature measurement system (using the Proteus simulation). Proteus analog circuit+ PIC C language source code (MPLAB V8.00) This is not using multiple I/O simulation of multi-channel temperature measurement Oh! See system functions: 1) by the parasitic power line data line, using MOSFET strong pull-up power supply to the DQ 2), power-on automatically search for available sensors and do CRC check (to achieve a Search ROM command) 3) alarm limit choice 4), polling shows the temperature, through the LCD1602 output 5), half-way pulled out or the temperature sensors are all cross-border police 6), using sound and light alarm mode can be used as the

功能描述： 利用AT89S51单片机的T0、T1的定时计数器功能，来完成对输入的信号进行 频率计数，计数的频率结果通过8位动态数码管显示出来。要求能够对2－40KHZ 的信号频率进行准确计数，计数误差不超过2/1-Functional Description: Using AT89S51 MCU T0, T1 timing counter function, to complete the input signal frequency counting, counting the frequency of 8 resulted in the adoption of dynamic digital tube display. Request to the 2-40KHZ signal frequency accurately count, counting error of less than 2/1

本程序功能是利用单片机控制用户板上的小键盘，将按下的键通过单片机的串口发送给PC机，在PC机串口助手显示出来。用行翻转法的方法来识别输入的键盘。 二、通过单片机将键盘按下的键在LCD上显示出来。 -This procedure is the use of single-chip control functions of the user on-board a small keyboard, the keys will be pressed through the single-chip serial port sent to the PC, the PC Serial Port assistants displayed. Line inversion method used to identify the method of keyboard input. Second, through the single-chip microcomputer keyboard keys pressed on the LCD display.

at89c51 读取写入24c64的C源代码-24c64 read write AT89C51 the C source code