单片机控制原理书

12864液晶屏驱动: 显示器片选0=CS1,1=CS2 BZPD 0=上8X8半字,1=下8X8半字 HZDH 0=显示汉字，1=显示动画-12,864 LCD Driver : Display- election CS1 = 0, 1 = 0 = CS2 BZPD on 8x8-word, a = half under 8x8 = 0 word HZDH show Chinese characters, animation shows a =

AVR 简介，介绍AVR单片机的原理，应用及编程过程。-AVR description

这是点阵程序 个人认为先学点阵再学lcd比较好 p0 p2分别接16*16点阵的高八位和低八位(纵向取模) p3口低四位接4-16线译码器（74ls154）译码器低电平为列选 消除鬼影的方法：-This is the program individual lattice lattice before you think lcd is better to learn p0 p2, respectively, then 16* 16 lattice of high and low 8 8 (vertical modulus) p3 I received a low four 4-16 Line Decoder browser (74ls154) low-level decoder for the elimination of ghosting out the election approaches:

how to use st mcu c langugue,cosmic

msp430f169 clk操作 430单片机有丰富的外围模块其中时钟可以有多种选择可以令单片机能在各种速度下运行-430 Singlechip msp430f169 clk operation has a rich peripheral module clock which can have a wide range of choices can make single-chip can run at various speeds

C51下编写的跑马灯程序，可以实现好几种图案的变换。-C51 prepared Marquee procedures can be achieved several transformation patterns.

本设计主要是运用单片机设计一个最小系统――电子时钟，它具有24小时计时功能，能够对时间进行调整，并且能实现时、分、秒的显示，同时还有内设闹钟，时间到时候会响铃，响铃时可以通过按键控制延时再启动或关断。与此同时还设置了整点报时功能；并采用采用了软件去抖的方法扫描键盘，动态刷新显示数码管，并通过查表实现译码输出时间等编程方法；-This design is the use of single-chip design of a minimum system- Electronic clock, it has a 24-hour timer function, capable of time to adjust, and can achieve the hours, minutes and seconds display, but also equipped with alarm clocks, time to When ringing the bell to ring when the button control can delay re-start or shutdown. At the same time also set up the whole point timekeeping function and adopt the use of the software to scan the keyboard shaking method, dynamic refresh display digital tube, and through the realization of decoding look-up table output time programming method

这是一个GPS方面的资料，可供想在嵌入式方面编程的人员参考-This is a GPS information, can be like in the embedded programming staff members

三菱梯形图转成51单片机HEX文件。 三菱软件写好梯形图，再运行转换软件，设定好51单片机的输入输出， 打开写好的梯形图，转换出的就是hex文件，烧录到51单片机，51单片机 就可以执行PLC的动作了。51单片机控制板价格便宜，可以代替简单场 合的PLC，控制成本降低。 1：把PWM转换后，在PWM文件下生成一个HEX文件。 2：生成的文件很大，51单片机要选用8K以上(AT89S52就是8K)储存量的。 3：把HEX文件下载到单片机就可以用了。 -Mitsubishi ladder into 51 single-chip HEX file. Mitsubishi software written ladder, and then run the conversion software, set 51 single-chip input and output, open ladder-written, conversion is a hex file, burn to 51 single-chip, 51 single-chip microcomputer can be implementation of the action of PLC. 51 Single-chip panel prices, can replace the simple occasions PLC, control and lower the cost. 1: after the PWM converter, PWM documents generated in a HEX file. 2: generate a lot of paper, 51 single-chip 8K to choose more than (AT89S52 is 8K) storage capacity. 3: The HEX file can be downloaded to a single-chip microcomputer used.

CAN 驱动程序 源码 经军DEVICENET的前提！-CAN driver source code as a prerequisite for military DeviceNET!