A small keyboard program, there are nine buttons, through the 422 control other...

美的的一个吸尘器程序 -The United States, a vacuum cleaner process

ad转换的例子 基于89C2051的电压采样程序-ad conversion based on the example of the voltage 89C2051 sampling procedures

自己keil C51写的X25045驱动，调试通过-their written X25045 driven through debugging

* 硬件结构： PA0-5对应６个ＬＥＤ数显管的位 ，PC0-7对应各ＬＥＤ数显管的段 ，PB4-7为键盘。 * 软件描述： 上电后，时钟从00.00.00（时/分/秒）自动走时，在走时状态时 ， 按PB4（设定 * 键）超过3秒可循环选择调整时间/工作参数 ，接着按PB5以确定选择的操作 ，进入调整操作后 ， * 按PB5选择欲调整参数，按PB6（增加键）完成调整参数操作 。按PB7，进入时控运行，PB1亮， * 再按PB7停止时控运行，回显走时。在定时到时，PB0点亮。- * Hardware architecture: PA0-5 corresponds 6 LED numbers to reveal the tube the position, PC0-7 corresponds each LED number to reveal the tube the section, PB4-7 is a keyboard. * Software description: After on electricity, clock from 00.00.00 (when/a minute/second) is in luck automatically, when is in luck the condition, according to PB4 (hypothesis * The key) surpasses for 3 seconds to be possible to circulate the choice time/operational parameter, then presses PB5 by to determine the choice the operation, after enters the adjustment operation * Wants according to the PB5 choice to adjust the parameter, (increases key) according to PB6 to complete the adjustment parameter operation.According to PB7, enters when controls the mov

/* 程序详细功能介绍： *当按下按键P3.3 ，AT89S51单片机产生“叮咚”声从P3.2端口输出 *程序设计方法 * 1． 我们用单片机实定时/计数器T0来产生700HZ和500HZ的频率，根据定时/计数器T0，我们取定时250us， * 因此，700HZ的频率要经过3次250us的定时，而500HZ的频率要经过4次250us的定时。 * 2． 在设计过程，只有当按下SP1之后，才启动T0开始工作，当T0工作完毕，回到最初状态。 * 3． “叮”和“咚”声音各占用0.5秒，因此定时/计数器T0要完成0.5秒的定时，对于以250us为基准定时2000次才可以。 */-/* Procedure detailed functional Introduction:* When pressing the button P3.3, AT89S51 Singlechip a

汽车启动设计参考电路及程序代码。PIC单片机设计，汇编代码。-Auto start the design reference circuitry and program code. PIC microcontroller design, assembly code.

Keil C做的8个LED灯循环左移右移-Keil C do eight LED lights cycle bits shifted to the right

凌阳的LCD演示原码,里面还有LCD的使用说明.

/*P89CXX编程控制CPU接收和控制程序*///定义编程需要的CPU类型0:P89C51 1:P89C52 2:P89C54 3:P89C58 4:P89C51RC 5:P89C51RD

这是参加电子设计大赛时的作品：红外遥控小车：用红外线通过一块AT89S52单片机发射信号即编码，并用红外接收头接收信号；接着再用另一块AT89S52单片机对红外发射出的信号编码进行解码，最后再用一块AT89S52单片机用解码所得码值编写程序后驱动步进电机。步进机功能启动后不仅能使受控小车向前后左右四个方向前进和转弯，而且还能控制小车再地上转动并留下方形或圆形等形状。-This is the time to participate in Electronic Design Contest works: infrared remote control car: Using infrared transmission signal through an AT89S52 microcontroller that is encoded and used infrared receiver to receive the first signal and then using the other an infrared emitting MCU AT89S52 code and decode the signal and finally an AT89S52 microcontroller then proceeds with the decoding key value of the preparation of procedures to drive a stepper motor. Stepper machine function activated not only make the car forward in a controlled direction and after about four turns, but also to control the car and then turned and left the ground such as square or round shapes.