msp430f21x1架构概述

压缩文件包括电磁炉的控制程序和其原理电路图！方便大家阅读程序，配合原理图阅读！-compressed files including Induction Cooker control procedures and its tenets circuit! To facilitate reading the procedure to incorporate the diagram read!

使用proteus和Keil联调SCM51,此例程精讲了P0口匚用-The use of proteus and Keil FBI SCM51, this routine I精讲the匚with P0

本程序用于MICROCHIP 24LC64 EEPROM的读写。本程序不使用芯片级联方式， 请将A0，A1，A2 管脚接至低电平。本程序使用IOC6作为SDA，IOC7作为SCL。 程序中的地址空间最大可至64K：24LC00-16-0，24LC01-128-8，24LC02-256-8， 24LC04-512-16，24LC08-1K-16，24LC16-2K-32，24LC32-4K-32，24LC64-8K-32， 24LC128-16K-64，24LC256-32K-64，24LC512-64K-128，读写数据均为8bits。 以上器件的格式为（型号-地址空间-页大小）不同器件的页大小不同，因此页写 程序需作相应修改，其他字节写，随机读以及顺序读程序均相同-This procedure for the MICROCHIP 24LC64 EEPROM read and write. This procedure does not use chips cascade way, please A0, A1, A2 pin to low level access. This procedure used IOC6 as SDA, IOC7 as SCL. Process address space available to the largest 64K: 24LC00-16-0, 24LC01-128-8, 24LC02-256-8, 24LC04-512-16, 24LC08-1K-16, 24LC16-2K-32, 24LC32-4K- 32,24 LC64-8K-32, 24LC128-16K-64, 24LC256-32K-64, 24LC512-64K-128, read and write data are 8bits. The format for the above device (Model- address space- page size) of different devices of different sizes of pages, so page written procedures need to be amended accordingly, and other bytes to write, rand

单片机C语言初学教材，其中包括了很多关于单片机C语言的知识

用L293步进电机驱动芯片做的步进电机驱动器.-Stepper motor driver using L293 chip to do the stepper motor drive.

这是自己写的关于PS2键盘接口的程序，和单片机的接口，用汇编写的，测试成功，与图形点阵液晶联合使用，不过液晶程序没有上传-This is his writing on the PS2 keyboard interface procedures, and the microcontroller interface, with a compilation of written test successfully, and graphics dot-matrix LCD joint use, but not to upload procedures LCD

使用CYAN单片机的ECOG1开发板连接SIM300C的GSM模块开发的短信收发程序.供UART和AT指令编程者参考-using CYAN,sim300c, to send and receive SMS.

320*240点阵液晶模块驱动程序,控制芯片为SED1335；128*64点阵液晶体驱动程序，控制芯片为ks0108.-320* 240 dot matrix LCD driver, controller chips for SED1335; 128* 64 dot-matrix LCD driver, controller chips for ks0108.

完全实用化的020 SMBUS程序（与时钟PCF8563通信）.rar经调试,很正确的.-Entirely of 020 SMBUS utility program (with the clock PCF8563 communication). Rar by debugging, it is correct.

PROTEL15.PCB是较老的PCB软件,我还在用-PROTEL15.PCB is PCB older software, I still use ...