24LC01 24LC256 to the general program is EEPROM 24LC01

源码公开的MCS 51 单片机的宏汇编器 Macro Assembler of MCS MCS-51 micro controller Version 0.12 这是一个应届生写的习作 尽管这个软件A51 还未完全达到满意的效果不过与Keil 公司的A51 配合起来使用还是不错的 公开源码和文档的目的是希望能够给一些爱好者作为学习编译原理和C 程序设计的靶子同时也希望有更多的热心人参与修改源码直至更加完善 来自周立功公司-MCS 51 open-source SCM macro assembler Macro Assembler of MCS MCS-51 micro controller Version 0.12 This is a year of Health to write assignments A51 even though the software is still not yet fully satisfactory, however the effect of the A51 and Keil company with up or a good use of open source code and documentation which aims to compile a number of enthusiasts as a learning theory and C programming target but also hope that more and more enthusiastic to participate in modified source code until a more complete company from weeks Ligong

液晶屏显示程序，主要对各按键处理做了很好的处理，可随意改动各按键，通讯采用MODBUS ASCII 可以控制台达变频器的起停及速度控制-LCD display program, the main keys to deal with a very good, may be arbitrarily changed the keys, communications using MODBUS ASCII converter can console cease and the speed control

A/D转换，转换结果用液晶显示出来，液晶是OCMJX12864。显示的结果是数字量。使用的是ADC0809。（有原理图）-A/D conversion, conversion results liquid crystal display, LCD is OCMJX12864. The result is digital displays. Are using the ADC0809. (With schematic diagram)

红外遥控接收 ORG 0000H LJMP START 转入主程序 ORG 0010H START: MAIN: JNB P2.2,IR LJMP MAIN 以下为进入P3.2脚外部中断子程序，也就是解码程序 IR: MOV R6,#9 SB: ACALL DELAY882 调用882微秒延时子程序 JB P2.2,EXIT 延时882微秒后判断P3.2脚是否出现高电平如果有就退出解码程序 DJNZ R6, SB 重复10次，目的是检测在8820微秒内如果出现高电-infrared remote control receiver ORG 0000H LJMP START into main program ORG 0010H START : MAIN : JNB P2.2, IR LJMP MAIN below to enter P3.2 foot external interrupt subroutine, which is decoding procedures IR : MOV R6, SB# 9 : Calling ACALL DELAY882 882 microsecond delay subroutine JB P2.2, EXIT 882 microsecond delay after the judgment whether there P3.2 feet to I quit if decoding procedures DJNZ R6, SB repeated 10 times, the purpose is to test if within 8,820 microsecond high

自制小时钟 可以遥控调节时间，采用315M 2262 ，2272 收发模块 发来给新手看看 -Self-made small-time clock can be adjusted remotely, using 315M 2262, 2272, sent to the transceiver module to see if novice

利用单片机实现SD卡读写程序，比较通用，大家可以参考，希望对你有所帮助。-Use of SCM SD card reader program, a more generic, we can refer to, want to help you.

刚学了一点上位机控制,感觉这个程序不错,适合初学者,与大家共享!-Just learn to control that PC, I feel pretty good this procedure is suitable for beginners, with everyone sharing!

利用单片机的P32管脚进行测量频率,计时很精确-P32 pin single-chip computer to measure the frequency, timing is very precise

基于AT89C2051的照明系统控制程序，实现照明设备的自动控制。-AT89C2051-based lighting systems control procedures, to achieve automatic control of lighting equipment.

这是msp430与1335的接口控制程序，控制320*240的液晶显示驱动。-This is the MSP430 with the 1335 interface control procedures, control 320* 240 LCD display driver.