LPC2106为PROTEUS仿真程序，keil UVIS编译环境…

c8051FXXX系列单片机开发工具 PDC U-PDC U-EC 使用手册，及IDE KEILC 使用方法，供初始C8051F的人员使用-c8051FXXX Series MCU Development Tools PDC U-PDC U-EC the use of manuals, and IDE KEILC use for the initial use of the C8051F

LM3S89XX ARM(CORTEX-M3) 内部看门狗原代码，周立功提供-LM3S89XX ARM (CORTEX-M3) internal watchdog the original code, Zhou Ligong provide

三相步进电机的三相六拍工作方式，正转的绕组通电顺序：A、AB、B、BC、C、CA、A，反转的通电顺序：A、AC、C、CB、B、BA、B、A。 由于步进电机转子有一定的惯性以及所带负载的惯性，故步进电机的工作过程中不能及时的启动和停止，在启动时应慢慢的加速到预定速度，在停止前应逐渐减速到停止，否则，将产生失步现象。 步进电机的控制问题可总结为两点： 1、产生工作方式需要的时序脉冲； 2、控制步进电机的速度，使它始终遵循加速、匀速、减速的规律工作。 -Three-phase three-phase stepper motor six shot work, is to order the winding power: A, AB, B, BC, C, CA, A, reverse the order of power: A, AC, C, CB, B, BA, B, A. As the stepper motor rotor has a certain degree of inertia, as well as brought about by the inertia load, the stepper motor during the course of work should not start and stop time, start to be slowly accelerated to a predetermined speed, the stop should be to slow down gradually to the stop, otherwise, will result in out-of-step phenomenon. Stepper motor control problems can be summarized in two points: one, resulting in the need to work the timing pulse 2, control the speed of stepper motor, so that it always followed acceleration, velocity, deceleration of the law of the work.

PID C 语言与Matlab 应用，看了后可以编程了-PID application

ks0108 12864 液晶的C语言驱动-ks0108 12864 LCD C-language-driven

条码读入CPU 1. 与条码读入器的通讯 1.1 采用标准的UART通讯协议，波特率为9600，没有校验位，一个停止位。 1.2 通讯的过程是单工的，数据流总是从条码读入器到CPU。 1.3 正常的数据传送总是以一个换行符开始，六个数字，以一个回车符结束。 -51

台电T50电路图，用于研究T50的电路设计，以及Rk2706的共模设计方案-Taipower circuit T50, T50 for the study of circuit design, as well as the common-mode Rk2706 design

各种单片机反汇编工具包，现在用的人少了，但还是有用的东西，想用的就下吧-compilation of various anti-SCM tool kit, now with fewer people, it is still useful things and to use it in the next

PIC单片机程序设计基础 入门教程.-PIC Design Basics Guide.

单片机c语言编程，学习用c语言单片机编程，学习学习的开始-SCM c programming language, to study c microcontroller programming language, learn from the beginning