QG8_demo学习板开发板例程 显示的例程，辛苦找来。 经过验证是正确的。...

这是sd/mmc卡程序的第三部分，后面还有！-This is the sd/mmc card the third part of the procedure and there are!

=== =时钟20:6=== === == 应先初始化状态寄存器 tx1714 EQU 7FFH PA EQU 05H PB EQU 06H PC EQU 07H PD EQU 20H IAR EQU 00H 间接寻址寄存器 TMR0 EQU 01H 定时器 STATUS EQU 03H 状态寄存器 BSR EQU 04H bank选择寄存器 PORTA EQU 05H I/0端口寄存器 PORTB EQU 06H I/0端口寄存器 PORTC EQU 07H I/0端口寄存器 PORTD EQU 20H I/0端口寄存器 PULL EQU 21H PULL-High上拉寄存器 WAKEUP EQU 22H 唤醒控制寄存器－－被用来设定watchdog允许和禁止 IRQM EQU 23H 中断屏蔽寄存器 IRQF EQU 24H 中断标志寄存器 WDTSEL EQU 25H -=== === = clock 20 : 6 === === === == should first register initialization state tx1714 EQU 7FFH EQU PA PB EQU 05H 06H 07H PC EQU PD EQU 20H IAR E QU 00H indirectly addressable registers TMR0 EQU 01H timer STATUS EQU Mr send state BSR EQU-deposit bank in the 04H choice Register PORTA EQU 05H I/O ports Register P ORTB EQU 06H I/O ports Register PORTC EQU 07H I/O ports Register POR TD EQU 20H I/O ports Register PULL EQU 21H PULL-High pull Register WAKEUP EQU 22H awaken control registers-- were used to set watchdog allowed and prohi

AVR单片机，mega16开发板，按键扫描数码管显示程序。-AVR single-chip, mega16 development board, key scan digital tube display program.

51必备-51 essential

《单片机仿真入门实用教程》实例(包括源代码) 单片机仿真教程。-"PROTEUS Practical Guide Getting Started" examples (including source code) Proteus-based simulation of single-chip microcomputer.

John Catsoulis编写的Designing Embedded Hardware 。介绍了汇编语言，SPI,I2C,串口，usb,网口等硬件电路设计。模拟电路设计，AVR单片机原理-John Catsoulis prepared Designing Embedded Hardware. Introduction of assembly language, SPI, I2C, serial, usb, network hardware such as circuit design of the mouth. Analog circuit design, AVR Singlechip Principle

1602显示测试程序-1602 shows test procedures

可用于PIC单片试验用，12M晶振，形成10毫秒中断 第一次上传东西，试试看，-PIC chip can be used to test, 12M crystal, the formation of the first 10 ms interruption upload things, give it a try,

基于转换器的压力测量与精度分析-converters based on the pressure measurement and analysis accuracy

winavr，atmega8，44780，1602液晶屏程序-winavr, atmega8, 44780,1602 LCD screen procedures