这是点阵程序 个人认为先学点阵再学lcd比较好 p0 p2分别接16*16点阵的高八位和低八位(纵向取模) p3口低四位接4...

c8051f021单片机资料-c8051f021

MC9S12DG128B，包含了时间中断、光电检测、舵机控制、电机驱动、实时控制等功能。有相关注释。-MC9S12DG128B, includes a time interrupted, photoelectric detection, steering control, motor-driven, real-time control functions. Relevant Notes.

把所有端口的同时置高置低,不断闪烁 2 p1 口3 路流水灯理解2 进制数与端口的关系 3 单片机的加法:把52h+0fch 结果送p1 口 4 单片机的乘法:把ff*03h 结果送p1 5 单片机的二进制加法 6 单片机的两位计数器 7 学习单片机的逻辑运算 8 进一步学习单片机的逻辑运算 9 循环移位指令的流水灯 10 理解熟悉散转结构的程序 11 位操作指令的学习 12 比较指令的学习与cy位-All ports at the same time the high home ownership low, and constantly flashing 2 p1 I 3 way light water 2 hexadecimal understanding the relationship between the number of 3-port MCU adder: the 52h+ 0fch results sent p1 mouth 4 Singlechip multiplication: ff* 03h results to send binary adder p15 SCM SCM 6 2 7 learning Singlechip counter logic operations further study 8 MCU 9 cyclic shift logic operations instructions flowing light 10 scattered understanding of familiar procedures to the structure of 11 operating instruction instructions learn learning 12 compared with the cy-bit

320×240液晶驱动源程序-320 240 LCD driver source

430学习书籍,好东西,希望大家下载-430 learning books, good things, I hope everyone downloads

硬盘控制电路以及原程序Demo,知识是属于全人类的。能将自己的成果无条件与人共享是伟大和受人尊敬的，同时也是一件幸福的事。 由于我想得到幸福和受人尊敬，所以我也开放我的工作成果。（其实也不算什么工作成果，匆匆忙忙用了一晚写的，见笑了。 在此感谢邵春伟同志，我在研究ata协议的时候参考了他写的程序） -drive control circuit and the original procedure Demo, knowledge is the whole of mankind. The results can unconditionally with the people sharing is great and respected, but also a happy thing. I want happiness and well respected, so I open my work. (What is not a work haste spent a night writing, a laughing stock. This would SHAO Chun-wai comrades, I studied ATA agreement for the reference to the writing process)

震动强度的测量 ad转换 八段数码管显示 51单片机-ad leddisplay

51单片机对AT45D041卡（大容量IC卡）的读写程序 把.rar改成.c即可-51 micro AT45D041 card (large-capacity IC card) reading and writing procedure. Rar changed. C can

公共汽车报站器,基于51-bus stop-based 51

第 一章 电路原理分析 1-1 显示原理 1-2 数码管结构及代码显示 1-3 键盘及读数原理 1-4 连击功能的实现 第 二 章 程序设计思想和相关指令介绍 2-1 数据与代码转换 2-2 计时功能的实现与中断服务程序 2-3 时间控制功能与比较指令 2-4 时钟误差的分析 附录A 电路图 附录B 存储单元地址表 附录C 输入输出口功能分配表 附录D 定时中断程序流程图 附录F 调时功能流程图 附录G 程序清单 -clock circuit based on AT89C51