基于PSE061A(凌阳单片机)多功能语音控制小车

电力载波抄表系统里的电力载波采集器,采集数据再通过RS485向主站发送.-Meter Reading System Power Line Carrier Power Line Carrier" s collector, collecting data through RS485 sent to the master station.

智能门禁系统采用凌阳十六位单片机作为系统控制核心，利用其强大的语音识别功能，不仅实现了语音播放功能，完成了语音提示的要求，而且实现了语音控制门禁系统；利用其内置的Flash闪存，实现了密码的断电保护。除此而外，在键盘输入方面，强大的功能选择键满足了系统的要求；16*2液晶显示器的选择使操作要求清晰明了。此套智能门禁系统强烈体现了其人性化的一面-Intelligent access control system uses the Sunplus 16 single-chip system control as the core, to use its powerful voice recognition features, not only realize the voice playback, the voice prompts to complete the requirements, but also realize the voice control of access control systems the use of its Purchase of Flash memory, realize the power to protect your password. Furthermore, in keyboard input, the choice of powerful features to meet key requirements of the system 16* 2 LCD display options so that operating requirements clear. This set of intelligent access control system strongly reflects its human side

i2c总线eeprom读写程序 可以读些从21c01--24c512的i2c总线eeprom芯片-i2c bus EEPROM read and write procedures can read more from 21c01-- the i2c bus 24c512 chip EEPROM

w77e58 双串口 液晶显示源程序 c语言编写-w77e58 dual serial LCD source language c

用51汇编语言设计的DTMF发生器程序 输出到PI的每次间隔是52个指令周期 主频：6M，6M/12=0.5M,每个指令周期：2uS 即每次输出到P1的时间间隔是122uS 指令周期数：52 + 9 = 61-51 assembly language using the design process DTMF generator output to the PI for each interval is 52 instruction cycle speeds : 6M, 6M/12 = for 0.5 per instruction cycle : 2uS that each output to the P1 time interval is 122uS instruction cycle : 52 9 = 61

591单片机CAN模块A51DEMO程序-591 SCM CAN module A51DEMO procedures

LPC900 FLASH单片机实现电话远程遥控-LPC900 FLASH MCU phone remote control

这是一个比较典型的PID处理程序，在使用单片机作为控制cpu时，请稍作简化，具体的PID 参数必须由具体对象通过实验确定。由于单片机的处理速度和ram资源的限制，一般不采用浮点数运算，而将所有参数全部用整数，运算 到最后再除以一个2的N次方数据（相当于移位），作类似定点数运算，可大大提高运算速度，根据控制精度的不同要求，当精度要求很 高时，注意保留移位引起的“余数”，做好余数补偿。这个程序只是一般常用pid算法的基本架构，没有包含输入输出处理部分。-This is a typical PID process, as in the use of SCM control cpu, please slightly simplified, specific PID parameters to be specific targets identified by experiments. As SCM processing speed and ram resource constraints, generally do not use floating-point operations, and will use all the parameters of all integers, and the final calculations to divide one of the Nth 2 data (the equivalent displacement), will count for a similar operation, it will greatly increase the computing speed, control Accuracy of different requirements and high precision, displacement caused reservations to the attention of the "I", which I do several compensation. This procedure is commonly used algorithm pid the basic structure does not include input and output processing.

凌阳61板锯齿波发生程序，可以在产生示波器上产生锯齿波-Sunplus 61 sawtooth board programmed, you can have a sawtooth generated Oscilloscopes

一个关于高速单片机红外编码解码的例程，希望对做红外通信的朋友有所帮助。-on a high-speed infrared codec SCM"s routines, and I hope to do the infrared communications friends help.