基于ＰＩＣ１６单片机的门铃控制程序，已经通过编译

1602LCM液晶显示屏的驱动函数和实例-1602LCM LCD driver functions and examples

学习C51时写的中断程序,提供给刚学单片机程序的朋友参考-C51 when learning to write the interrupt procedure, available to just school friends Singlechip procedure reference

本文给出了一种以80C31为主控CPU的固定电话短信息终端的设计，从系统软硬件两个方面说明了固定电话短信息终端的设计方法和各个部分的工作原理 -This paper proposes a 80C31 CPU for controlling the fixed telephone short message terminal design, system software and hardware from the two showed that the fixed telephone short message terminal design methods and various parts of the work principle

基于中断控制的声光报警器的设计.采用中断方式，设计一个声光报警器的硬件电路和控制程序。程序运行时，一旦8位开关信号量状态满足设定条件，就触发中断，使发光二级管按规律闪烁，同时扬声器播放一段音乐。 硬件设备包括一台微机、一个MFID微机实验箱、一块T型板，2输入四与门 74ls08、8位总线驱动器 74ls245、LM386A音频放大器、排阻、扬声器各一个，发光二极管8个，470uF电容2个、104电容4个，插线若干。 -Interrupt-based control of sound and light alarm design. Using interrupt mode, designing a sound and light alarm hardware circuits and control procedures. The program is running, once the 8-bit switch signal to set the amount of state to meet the conditions to trigger interrupts, so that light-emitting diode flashes according to the law, while speakers play a piece of music. Hardware includes a computer, a computer simulation, MFID box, a T plate, 2 input 4 and gate 74ls08, 8-bit bus driver 74ls245, LM386A audio amplifier, exclusion, speakers of a light-emitting diode 8, 470uF capacitor 2 a, 104 capacitors 4, plug-line number.

用DSPIC306011完成的数控逆变电源，完成以下功能：键盘，液晶，串口，spwm，ADDA 使之能构将幅度，频率，功率可调-With the completion of the NC DSPIC306011 inverter power source, complete the following functions: keyboard, LCD, serial, spwm, ADDA conformation so that it can be amplitude, frequency, power adjustable

SPI接口AD转换器代码 本代码实现了对串行（SPI）接口的软件模拟 这是在一个项目中要用到SPI接口的器件，调试成功，可以在WAVE下编译通过，可以直接调用 SPI接口AD转换器代码 2002/3/9 design by elven-SPI AD converter code of the source implementation of the serial (SPI) interface software simulation This is a project that will be used SPI interface devices, debug successful, the compiler through WAVE, and can directly call SPI AD converter code 2002/3/9 by design"s Eleven

此程序是用于AVR单片机驱动FLASH的,对于用AVR单片机进行开发的朋友,提供了一个例程,还有对于对使用FLASH没有经验的朋友也有很好参考价值-this procedure is used AVR Flash Drive, AVR for use for the development of a friend, provides a routine, There FLASH for the right to use the lack of experience has become a good friend reference value

基于无线通信模块的流程设备

这功能实在太强大了，你下载来看看就知道了，太精彩了啊。-This function is simply too strong, you take a look at the download will know, too wonderful ah.

DTMF编码芯片HT9200的51接口程序。输入参数R2表示发送数据个数，输入数据与发送数据与DTMF码的关系:00H-0 01H-1 02H-2 03H-3 04H-4 05H-5 06H-6 07H-7 08H-8 09H-9 0AH-A 0BH-B 0CH-C 0DH-D 0EH-* 0FH-#。详细说明参考文件内-DTMF encoder chip HT9200 51 interface program. R2 said input parameters to send data distribution, data entry and send data with the DTMF code : 00H-0 01H- 02H-2 Mr- 3 in the 04H-4 05H-5 06H-6 07H-7 08H-8 7-9 0AH-A 0BH- 0CH B-C 0DH-D 0EH-* 0FH-#. Detailed information paper