之前看过论坛上有一个C8051和S3530A的通信程序，但我认为很复杂而不具有通用性，我自己写的一个3530通过I2C总线与单片机的通信程序,虽然很短,但是很实...

在对存储空间要求非常严格的嵌入式系统中用CPU下载CPLD的代码，比如51系列的单片机。-storage space in the very strict requirements of embedded CPU system used to download CPLD code, for example, the MCU 51.

C8051F020/1/2/3混合信号ISP FLASH微控制器数据手册（中文的哦）-C8051F020/1/2/3 Mixed-Signal ISP FLASH MCU Data Sheet (Chinese, Oh)

单片机接口技术实验指导 单片机接口技术实验指导-Single-chip interface technology to guide the experimental single-chip interface technology to guide the experimental

针对USB2SPI128芯片的上位机驱动程序的源代码，主要是联通PC机的底层USB驱动和下位机单片机的通讯。-USB2SPI128 chip host computer for the driver source code, mainly to China Unicom PC-bottom USB drive and the next crew microcontroller communications.

健身器械面板显示程序，可以显示时间，距离，速度等，并具有三个按键进行相应的操作-fitness equipment panel display program can demonstrate that time, distance, speed, and with three buttons for the appropriate operating

用凌阳单片机控制显示电压步进，增减，并输出模拟电压

* 硬件结构： PA0-5对应６个ＬＥＤ数显管的位 ，PC0-7对应各ＬＥＤ数显管的段 ，PB4-7为键盘。 * 软件描述： 上电后，时钟从00.00.00（时/分/秒）自动走时，在走时状态时 ， 按PB4（设定 * 键）超过3秒可循环选择调整时间/工作参数 ，接着按PB5以确定选择的操作 ，进入调整操作后 ， * 按PB5选择欲调整参数，按PB6（增加键）完成调整参数操作 。按PB7，进入时控运行，PB1亮， * 再按PB7停止时控运行，回显走时。在定时到时，PB0点亮。- * Hardware architecture: PA0-5 corresponds 6 LED numbers to reveal the tube the position, PC0-7 corresponds each LED number to reveal the tube the section, PB4-7 is a keyboard. * Software description: After on electricity, clock from 00.00.00 (when/a minute/second) is in luck automatically, when is in luck the condition, according to PB4 (hypothesis * The key) surpasses for 3 seconds to be possible to circulate the choice time/operational parameter, then presses PB5 by to determine the choice the operation, after enters the adjustment operation * Wants according to the PB5 choice to adjust the parameter, (increases key) according to PB6 to complete the adjustment parameter operation.According to PB7, enters when controls the mov

单片机中用于相位差测量仪的c程序，开发环境是Iar。主要运用于430 单片机-Single-chip in for the c phase difference measurement procedures, the development environment is Iar. The main application of 430 single-chip microcomputer

用C编程实现的一个单片机报警系统！已经调试可以使用！是单片机大作业的一个！--A SCM alarm system. It is written in C language. It is a part of a big assignment on SCM.

1.The content is too simple 2.Is not a sourcecode or document 3.lost some files 4.Description is not detailed or not correct 5.Compressed file has password 6.Sourcecode duplicate or already exist