-
凌阳非接触式红外测温传感器的C51源程序。
凌阳非接触式红外测温传感器的C51源程序。-Sunplus non-contact infrared temperature measurement sensor C51 source.
- 2022-02-05 19:39:40下载
- 积分:1
-
linux移植过程分析,详细介绍了linux2.6的配置和裁减,很详细,每一项都有介绍,还有很多经验在里面,是不可多得的linux配置手册。...
linux移植过程分析,详细介绍了linux2.6的配置和裁减,很详细,每一项都有介绍,还有很多经验在里面,是不可多得的linux配置手册。-linux transplant process analysis, detailed information on the configuration and the reduction of linux2.6, very detailed and have each of the introduction, there are a lot of experience on the inside is rare linux manual configuration.
- 2023-03-24 07:30:05下载
- 积分:1
-
Design s3c44b0 examples of serial communication. have to send receive function
s3c44b0的串口通信设计例子.有发送接收功能-Design s3c44b0 examples of serial communication. have to send receive function
- 2022-03-26 08:43:52下载
- 积分:1
-
校园导游系统,查询景点信息,求最短路径等
校园导游系统,查询景点信息,求最短路径等-campus tour guide system, query attractions information, such as Shortest Path
- 2022-09-25 02:25:03下载
- 积分:1
-
STM8S 通用输入输出接口
本应用笔记提供简短说明示范固件发现的,预先在 STM8S003K3T6 单片机的闪存中。这个示范固件使使用的基本的 8 位定时器配置为 STM8S时基发生器来改变 LED LD1 的闪烁速度
- 2022-11-08 21:55:03下载
- 积分:1
-
对nand_flash的擦除、编程算法源码
对nand_flash的擦除、编程算法源码-right nand_flash the erasure, programming algorithm source code
- 2022-01-21 23:23:31下载
- 积分:1
-
MSP430f149上LCD显示的程序
MSP430f149上LCD显示的程序-MSP430f149 LCD display on the procedure
- 2022-01-28 13:10:12下载
- 积分:1
-
独立数字电压表使用多通道 ADC 代码
这是用于 IC2 代码的EDN 设计理念独立数字电压表使用多通道 ADC 提供了一个设计,使用一台仪器监视几个不同的电压。
- 2023-04-09 06:10:03下载
- 积分:1
-
T-Ker测试synchronization_communicationsemaphore部分的tk_cre_sem,tk_del_sem, tk_sig_sem, tk_wai_sem, tk_ref_sem在移植的uT-Engine上运行是否正常。
api的返回值正确与否,在ads上设断点观察,同时用Lpc2104上的LED显示(如果正确,则程序中设定的LED就闪亮)nel中的flag小实验程序-T- Ker test synchronization_communication tk_cre_sem part of the semaphore, tk_del_sem. tk_sig_sem, tk_wai_sem. tk_ref_sem transplantation in the UT-Engine running normal. Api return to the correct value, based on the ads breakpoint observation, Lpc2104 using the LED display (if correct, procedures were set on the flashing LED) nel flag of the small experimental procedure
- 2022-06-02 06:30:47下载
- 积分:1
-
This procedure is the routine display module, the access device for four eight l...
本程序是显示模块的例程,所接器件为四位八段led数码管,其中PTB0-PTB3
与数码管的位选相连接,PTB4,PTB5与74LS164连接确定你开发板上拨码开
关JP1(图片上的12)的两位和JP4(图片上的9)的5、6、7、8位处于on),
而其他位处于远离on!-This procedure is the routine display module, the access device for four eight led digital tube, which PTB0-PTB3 bit digital tube and connected to the election, PTB4, PTB5 with 74LS164 sure you connect the development of on-board DIP switch JP1 ( picture on the 12) two and JP4 (picture on the 9) of 5,6,7,8 located at on), while the other located at far away from the on!
- 2022-03-19 04:34:06下载
- 积分:1