lingyangdanpianji

说明：  冷风扇控制板程序开发，三挡触摸调档。完整程序。(Cold fan control board program development, three touch shift)

基于单片机的函数信号发生器的C语言代码，自己做的(Function signal generator based on single chip microcomputer C language code )

说明：  设置3个功能键：当某一功能键被按下后，进入相应的功能模式。3个功能有： 1）8路数据采集功能：通过调节可变电阻实现0-5V的电压输出作为8路输入信号使用，每路信号用2位LED显示采集的结果。报警：任意一路超过某一门限（可自己设定）时，发出报警（声音+灯闪烁，并通过灯指示是哪一路报警），同时停止采集。2）计数功能：利用计数功能键，实现每按一次按键，LED显示加1，从0-99计数。3）秒表功能：只用一个键控制。按下一个按键后时钟启动，从零开始计时，计时间隔0.01秒，再按一次后停止。再按一次后清零。如此循环。 本设计采用2个MAX7221串行驱动2个8路数码管显示，更节省单片机I/O口。(AD、count、countdown)

基于单片机的温度控制系统设计毕业设计是大学毕业时必完成的大作业，其中基于单片机的温度控制系统设计毕业论文用以描述整个设计的业务流图,E-R图,数据流图等范文 基于单片机的温度控制系统设计设计则是在某种开发语言上设计与实现的源代码或源程序.全套设计论文包括开题报告,答辩稿,外文翻译,需求分析,中期报告等资料. (Temperature Control System Based on Single Chip graduation graduating from college is a big job will be completed, in which the temperature control system design based on single-chip design thesis to describe the entire business flow diagrams, ER diagrams, data flow diagrams essay based on SCM design of temperature control system is in the design and implementation of a programming language source code or source code. complete design papers include opening report, the respondent draft, foreign language translation, needs analysis, interim reports and other information.)

8051单片机驱动ADS7846/ADS7843芯片,触摸屏被按下时,则ADS7846向CPU发中断请求.()

UCGUI3.90notes应用于STM32，移植到STM32非常实用(UCGUI3.90notes applied STM32, STM32 very practical transplanted to)

说明：  孵化环境温湿度监控系统设计！！！！！！！(Design of temperature and humidity monitoring system for incubation environment)

附件为小日本的50KW逆变器的方案，太阳能控制架构图，希望对大家有用。附件为小日本的50KW逆变器的方案，太阳能控制架构图，希望对大家有用。(Attached is a small Japanese 50KW inverter solutions, solar control chart, we want to be useful. Attached is a small Japanese 50KW inverter solutions, solar control chart, we want to be useful.)

ATmega64振动 舞动 雷击 监测，电力电线姿态检测，事实的提供给监控中心参考数据，监控人员作出相应的反应。(ATmega64 dancing lightning vibration monitoring, power wires attitude detection, the fact that the monitoring center to provide reference data, monitoring staff respond accordingly.)

说明：  用C语言编写STM32嵌入式程序，设计一个万年历系统，并用HX1230屏显示相关的时间信息。 基本要求： 1.C语言程序要求是模块化设计。 2.该万年历要求能显示时间（时、分、秒）、年月日及闹钟定时时间（分、秒）。 3.该系统由2-3个按键可调整显示的时间、年月日及闹钟定时时间，具体各个按键功能及编程方式自定。 4.该闹钟可以定时时间到，LED将发出提示闪光，且持续30s。 5.HX1230屏能驱动显示。 6.定时时间可被打断，即打断后恢复时继续计时。 7.设置闹钟报警功能； 8.利用STM32自带的温度传感器功能，使系统能显示当前环境温度值。(STM32 embedded program is written in C language, a calendar system is designed, and relevant time information is displayed on HX1230 screen. Basic requirements: 1. The requirement of C language program is modular design. The calendar requires that time (hours, minutes, seconds), year, month, day and alarm clock timing time (minutes, seconds) be displayed. 3. The system can adjust the display time, year, month, day and alarm clock timing time by 2-3 keys, and the function and programming mode of each key are self-determined. 4. The alarm clock can be scheduled to arrive, and the LED will give a prompt to flash, and lasts for 30 seconds. 5. HX1230 screen can drive display. 6. Timing time can be interrupted, i.e. when the interruption is resumed, the timing will continue. 7. Setting alarm function of alarm clock; 8. Using the temperature sensor function of STM32, the system can display the current environmental temperature)