实现了ucos_II在mini2440开发板上的移植，是初学ucos_II操作系统的好范例。...

本例程基于正点原子迷你stm32开发板，跑ucos-iii驱动DHT11(the program is run to stm32, it`s for ucos driver dht11 module, display temp&humi)

SC28L198是一个带有8个全双工异步通道UART的芯片，每个UART通道的接收器和发送器都拥有16字节深度的FIFO。芯片的每个UART通道除了基本的异步通信功能外，还可实现软件流控制（in-band flow control）、硬件流控制（out-of-band flow control）、以及多点模式（唤醒模式或RS-485模式）等，同时每个UART都有4个外扩的I/O引脚，每个外扩I/O引脚都为功能复用。 本资料包含完整测试程序，应用文档，电路原理图及PPT演示文档等。(SC28L198 is a full-duplex asynchronous channels with 8 chip UART, each UART channel receiver and transmitter have 16-byte deep FIFO. Each UART channel chip, the asynchronous communication addition to the basic functions, but also for software flow control (in-band flow control), hardware flow control (out-of-band flow control), as well as multi-point mode (wake-up mode, or RS-485 mode), etc., and each UART has a 4 outer expansion of the I/O pins, each outer expansion I/O pins are as functional reuse. This information includes a complete test program, application documents, the circuit schematic diagram and PPT presentation documentation.)

基于 ST 公司的 ARM-7 使用之 uC/OS-II 作业系统,此例程是移植于 STR-710 上的应用于 IAR EWARM V4.41A 工程编译,而 uC/OS 版本为 2.80-Based on ST

嵌入式实时操作系统（第2版）uC/OS-2源码学习嵌入式实时操作系统的优秀实例

uCOS_II for MSP430(内核源码和移植文档)-uCOS_II for MSP430 (kernel source and portable document)

51系列单片机的uCOS单片机编程进阶是个容易入门的系统-51 Series MCU uCOS Advanced Microcontroller Programmer is an easy entry system

实现Fujitsu-FFMC-16-V120 ucos系统移植-Realize Fujitsu-FFMC-16-V120 ucos System Migration

本文以问答方式介绍easyarm2100/2104移植 ucos系统遇到的常见问题-By question and answer way ,this paper gives us an view of the problems being frequently met when uCOS-II is ported to the easyarm2100/2104 development board

这个程序是4路抢答器的程序，这个程序实现的功能是：当主持人按下抢答键后，参赛选手才可以进行抢答。抢答时能发出声响，并通过七段数码管显示是哪位选手抢答的。这个程序在PIC单片机上测试过，效果良好(This program is 4-way Responder program, this program is to achieve the function: When the host pressed to answer in key, players can only answer in. Responder when audible, and through the seven-segment LED display which player is the answer in the. This program is tested on PIC microcontrollers, to good effect)

基于uCOS-II 的MMC/SD卡的读写源程序-UCOS-II based on the MMC/SD card read and write source code