for a remote field eddy current testing data acquisition system programming inte...

GSerial是一个DOS下串口通信程序，程序结构较好，能编出用中断方式接收/发送的多串口通信程序（龚建伟曾用它编过7串口通信程序）。Turbo C++ 3.0 Dos或 Win3X/9X/ME/NT/2K的DOS环境下运行-GSerial under DOS is a serial communication program, program structure better, can be compiled out with interrupt receiving/sending of multiple serial communication program (Dan has used its seven series serial communication procedures). Turbo C 3.0 Dos Win3X/9X/ME/NT/2K or the DOS operating environment

实现字符转换！需要在两台机子上运行，也可以把一台机子的两个com口连在一块！这样就行了！还需要一个串口调试程序，网上可以下载到！-achieve characters change! The need to run two machines, one Taiwan can the two com loom even in a mouth! So OK! Need a serial debugging procedures can be downloaded to the Internet!

基于消息的Windows串口通讯例子- Based on news Windows string mouth communication example

从编程实践的角度详细介绍windows环境下和dos环境下的串口通信的基本方法-programming practice from the perspective of detail windows environment and the environment dos serial communication base this method

介绍了Linux下的串口驱动的设计层次及接口, 并指出串口与TTY终端之间的关联层次(串口可作TTY终端使用)-Describes the serial port under Linux-driven design and interface level, and noted that the serial link between the terminal and the TTY level (TTY serial port can be used for end-use)

多文档界面设计配置文件读写串口操作串口封装类-Multiple Document Interface Design configuration file to read and write serial operation serial Packaging category

我所见过用VC写的最好的串口类，具有模拟单片机中断传输的方式，避免了查询传输CPU损耗和接收超时-I have ever seen VC was the best serial category, with simulation SCM interruption of transmission, so that the CPU for transmission and reception of overtime loss

从串口读取数据，有两种方法，1、每接收一个EV_RXCHAR,就用ReadFile读一次，这样我觉得太恐怖了。2、接收到一个EV_RXCHAR后，等一定数据量的CPU周期(GetTickCount),再一次性读取缓冲区里的数据。这样做，一般情况下不会有问题，但是，如果数据很多，过了“一定数据量的CPU周期”，还没收完数据怎么办？就会少读数据了。 我用三个线程序来完成串口数据的接收，其实就是第一种方法的变种： 一个侦听EV_RXCHAR,一个对EV_RXCHAR进行分析，其实就是超时判断。如果接收到一个消息后，一段时间没收到下一个EV_RXCHAR，就认为是一个数据包的结束。这个线程就会通知数据接收线程，进行数据接收。一般同一包数据，两个字符之间的时间间隔，应该很小了吧，而两个数据包之间的间隔，应该不会太小吧！（这个地方我不清楚，猜的:( :) ）最后一个线程，是接收数据的。-read data from the serial port, there are two methods, one, each receiving a EV_RXCHAR, on the ReadFile read, I think this vote. 2, received a EV_RXCHAR after a certain volume of data, such as CPU cycles (GetTickCount), and the one-time reader, the data buffer. To do so, under normal circumstances there is no problem, but if many of the data, and after a "certain amount of data the CPU cycles," also confiscated End Data how do? Few will read the data. I used three lines to complete serial data reception, the first method is a variant : an interception EV_RXCHAR, one pair of EV_RXCHAR analys

使用说明： 系统要求：WIN9X/ME/NT/2000 VC++6.0 且安装了VC ACTIVEX控件（在VC6安装时选上） 免费 简介：在VC++6.0中用MSComm控件编程，可以实现串口接收数据和发送数据，数据分别显示在接收框和发送框中。-Usage: System Requirements: WIN9X/ME/NT/2000 VC++ 6.0 and installed VC ACTIVEX controls (in VC6 installation selected) Free Introduction: In VC++ 6.0 using MSComm control programming can be achieved Serial receive data and send data, data were displayed on the receiver box and sent box.

12,14,16点阵汉字显示文件 12,14,16点阵汉字显示文件-12,14,16 dot matrix display Chinese characters files characters dot matrix display documents 12,14,16