用AT89C51单片机、LED数码管、按键、发光二极管等组成，实现…

16位串行AD芯片ADS8341的51单片机程序-16-Bit Serial AD-chip ADS8341 51 MCU program

如何使用USB总线接口在单片机系统中实现一个虚拟串口的原理和实现过程。在设计中，软件部分采用USB的CDC类标准来实现虚拟串口，这样可以使用操作系统（Windows,Linux）自带的驱动程序；在硬件设计中，使用自带USB从设备接口的AT89C5131单片机，提高了系统的集成度和可靠性-How to use the USB bus interface in single-chip realization of a virtual serial port system, the principle and implementation process. In the design, the software part of the adoption of USB-CDC class standards to achieve a virtual serial port, so you can use the operating system (Windows, Linux) comes with the driver in hardware design, the use of own USB interface from the device chip AT89C5131 machine, to improve the system integration and reliability of

at89s51，超级牛的教程，可以配合proteus仿真实验，-at89s51, super tutorial cattle will be in line with Proteus simulation experiment,

用msp430对x1228完全操作， x1228，一个串行的日立芯片，在单片机系统中，功能比较强大的日历芯片-with Controller fully operational right x1228, x1228, a serial Hitachi chip, the microcontroller system, functions more powerful chips Calendar

LPC900 FLASH单片机实现电话远程遥控-LPC900 FLASH MCU phone remote control

驱动显示屏硬件的栅和段的位数，控制16312的四个输出口数据。-Hardware display driver section of the gate and the median of the four control output 16312 data.

学习C51的同学， 可以看看这个 ， 有了这个， 保你学习进度可以提升3成速度。-If you wanna learn C51 more fast, this resoure maybe give you a helper.

IC卡操作软件:AT88SCl604芯片的操作模式有五种。它们是通过配PGM、RST、CLK等引脚信号及内部地址计数器(IAC)的状态组合来实现。 (1) 芯片复位操作： AT88SCl604有两种复位方式:上电复位和控制复位。 上电复位： 上电复位是当芯片加电时的最初状态。上电复位属于芯片 内部复位。它将使芯片内部所有的隐含标志复位到"0"状态。并使地址计数器复位到0位。 控制复位： 当CLK为低时，在RST脚上的一个下降沿将便芯片产生复位操作。 控制复位是将地址计数器复位到0位，而不影响任何内部标志的状态。-IC Card operating software : AT88SCl604 chip mode of operation there are five. They are allocated by PGM, RST, etc. pin CLK signal and the internal address counter (IAC) portfolio of the state is to be achieved. (1) chip reset operation : reduction AT88SCl604 two ways : power-on reset and reset control. Power-on reset : power-on reset when the chip is in power at the initial state. Power-on reset the internal chip is reset. It will enable all internal chip implied signs reset to "0" state. Make address counter reset to 0. Reset control : When the CLK for the low, the RST feet of a falling edge chips will have to reset operation. Reset control is to address counter reset to 0, without prejudice to any signs of internal sta

对MSP430片内温度传感器进行采样，输出温度到LCD * 程序使用单通道单次转换，温度显示的格式是华氏温度, * 带两位小数-On-chip MSP430 sample temperature sensor, the output temperature to the LCD* use single-channel single conversion, the temperature display format is Fahrenheit,* with two decimals

一个基本的平安钟控制程序，帮别人写的，学习的人可以看看，不错的。-Ping