伟福 WAVE6000 环境下 MCS51汇编调用C51例程

：介绍一种无人值守的停车场管理系统的设计。该系统前端主要由GsM 短信模块TC35i和AVR 单片机At― megal6组成，安装在停车场的每个进出口，通过接收车主的手机短信控制进出口道闸的开启并由短信扣取停车费用，各进出 口电路都与监控中心计算机连接。-: A unmanned car park management system design. The system front-end GsM messages by AVR module TC35i and At-megal6 composed of single-chip installed in the parking lot of each import or export through SMS to receive the owner to control the import and export of道闸open parking fees deducted by SMS , the import and export of circuits are connected with the monitoring center computer.

单片机内部定时器编程-Single-chip internal timer programming

三相步进电机的三相六拍工作方式，正转的绕组通电顺序：A、AB、B、BC、C、CA、A，反转的通电顺序：A、AC、C、CB、B、BA、B、A。 由于步进电机转子有一定的惯性以及所带负载的惯性，故步进电机的工作过程中不能及时的启动和停止，在启动时应慢慢的加速到预定速度，在停止前应逐渐减速到停止，否则，将产生失步现象。 步进电机的控制问题可总结为两点： 1、产生工作方式需要的时序脉冲； 2、控制步进电机的速度，使它始终遵循加速、匀速、减速的规律工作。 -Three-phase three-phase stepper motor six shot work, is to order the winding power: A, AB, B, BC, C, CA, A, reverse the order of power: A, AC, C, CB, B, BA, B, A. As the stepper motor rotor has a certain degree of inertia, as well as brought about by the inertia load, the stepper motor during the course of work should not start and stop time, start to be slowly accelerated to a predetermined speed, the stop should be to slow down gradually to the stop, otherwise, will result in out-of-step phenomenon. Stepper motor control problems can be summarized in two points: one, resulting in the need to work the timing pulse 2, control the speed of stepper motor, so that it always followed acceleration, velocity, deceleration of the law of the work.

BTF020实验程序-1 btf020开发板自带-Experimental procedures BTF020 development board comes with-1 btf020

单片机80c51的各类小程序的代码，适合初学者参考，在开发板上做实验-80C51 single-chip all small procedure code, suitable for beginners and reference, in the development of on-board to do experiments

对MSP430片内温度传感器进行采样，输出温度到LCD * 程序使用单通道单次转换，温度显示的格式是华氏温度, * 带两位小数-On-chip MSP430 sample temperature sensor, the output temperature to the LCD* use single-channel single conversion, the temperature display format is Fahrenheit,* with two decimals

摩托罗拉单片机的液晶LCD显示的C语言程序-Motorola MCU LCD liquid crystal display ........... C Programming Language

该源代码运行于89c51系列单片机上,可从输入FLEX二进制码流中解交织,处理CRC纠错,并最终解码出有效ASCII码数据.-the source code running on 89c51 MCU, FLEX can be imported from binary code stream deinterleave handling of CRC error correction. and finally decoding of effective ASCII data.

智能计数器，对外部信号脉冲进行计数，并将脉冲个数显示出来。 基本要求：计数至少65536个脉冲，并将脉冲个数显示出来。 -intelligent counter, the external signal pulse counting, pulse number will be displayed. Basic requirements : at least 65,536 Count pulse, and pulse number displayed.

超声波检测C代码源程序，单片机嵌入式软件程序设计-Ultrasonic testing C code source, single-chip embedded software programming