整有效。中间四个字节分别代表设备的地址、指令类型、指令参数1(OPT1)和指令参数2(OPT2)。设备在对这四个字节的内容进行译码后执行相应的操作...

注:protel电路图 1.INPUT12为高压气压和低压压传感器输入端. 2.OUTPUT为充气输出控制端. 3.当高低压有接地信号时,电机正转,气阀打开. 4.INPUT2低气压时有信号时,充气OUTPUT输出,充气电机转. 5.RS1与RS2是调节阀门距离用地 6.RS3是与气阀电机同步时,是气阀电机的转动圈数传感器. 7.RS4是调节延时时间用地-Note: protel circuit 1.INPUT12 and low-voltage high-pressure pneumatic pressure sensor input. 2.OUTPUT output control for the inflated side. 3. When the high and low pressure have a grounding signal when the motor is transferred, the valve opens. 4.INPUT2 low pressure when there is signal output OUTPUT inflatable, inflatable motor switch. 5.RS1 and RS2 is the regulator valve from the land 6.RS3 synchronous motor with the valve, the valve motor is rotating circle the number of sensors. 7.RS4 delay time to regulate land

开发环境为：iarEWARM5.20 语言为c语言 2378的启动文件，为EWARM5.20 例程中的文件 利用lpc2378的io口控制ocmj12232c-1液晶的程序。程序有详尽接口说明和完整的注释。ocmj12232c-1是st7920控制的显示模块。使用lpc2378移植的程序这是第一个。-Xi Yuan-kai为alas iarEWARM5.20 To:为c Pang Pang Sheng Sheng-hung 启 cavity 2378 ， glass text为bird

硬件电路相当简单的音乐播放的c51仿真及c程序-Relatively simple hardware circuit of the C51 music player simulation and c procedures

电动自行车控制器详细原理图，对无刷电机控制开发有帮助-Electric Bicycle Controller detailed schematic diagram of brushless motor control development help

请将OpenPet.ico 放在c盘文件下 当然你也可以放在程序目录，那就要修改程序 将private Icon img = new Icon(@"C:OpenPet.ico") 改为private Icon img = new Icon("OpenPet.ico") -request OpenPet.ico on c disk Document Of course, you can be put on the directory. it is necessary to revise procedures to private Icon img = new Icon (@ "C : OpenPet.ico ") to private Icon img = new Icon (" OpenPet.ico ")

DownLoad_sst39sf010.zip--嵌入式系统中关于SST39SF010的FLASH的BOOTLOADER源程序(KC51)-DownLoad_sst39sf010.zip--embedded system on the FLASH SST39SF010 source of BOOTLOADER (KC51)

flash程度源代码,该程度经过反复测试,没有问题-the degree of flash source code, the extent of repeated testing, there is no problem

freescale最新的几款加速度传感器资料，包括SPI接口的，IIC接口的。其加速度测量范围从1.5g到10g-freescale the latest information on several acceleration sensors, including the SPI interface, IIC interface. Its acceleration measurement range from 1.5g to 10g

MB90092文件，富士通MB90092的驱动程序 -MB90092 paper, Fujitsu MB90092 driver