Realize a simple statement with dsp output deal with the procedures to run in th...

TI公司28XDSP控制永磁同步电机PMSM 控制系统调试源码。-TI company 28XDSP control of permanent magnet synchronous motor PMSM control system source code debugging.

seed-dec6416用户指南，开发板带的-seed-dec6416 User Guide

在DSP上运行的DTMF（双音多频）解调程序-running on the DSP DTMF (Dual Tone Multi-Frequency) demodulation process

统一设定带宽（BandWidth）、脉宽（TimeWidth）、采样率（Fs）、脉冲重复频率（PRF）、雷达射频（RF）、噪声功率（NoisePower），用MATLAB产生16个线性调频（LFM）脉冲信号，每个脉冲有4个目标（静止，低速，负高速，高速），前3个目标速度和距离固定，第4个目标的速度和距离与学号有关。有3个目标的幅度相同，第3个目标幅度是另3个的一半，且距离与第2个运动目标相同。依次做如下处理：2.1.1 脉压2.1.2 相邻2脉冲做MTI（即相邻2个脉冲相应相减），产生15个脉冲2.1.3 16个脉冲到齐后，做MTD，输出16个多普勒通道2.1.4 改变PRF后，利用两次PRF下不同的速度结果，求不模糊速度2.1.5 选做：对MTD结果做CFAR（恒虚警）

motion Jpeg 在SPI DSP平台优化好的代码-motion Jpeg in good SPI DSP platform optimized code

tms320lf2407a 和74595芯片接口实现７段数码管显示程序-err

利用定时器中断制作方波发生器，通过LED灯的暗亮时间来测量其周期-Use timer interrupt the production of square-wave generator, through the dark bright LED lights to measure the cycle time

1、（1）32bit乘法的指令解释 （2）volume1的load.asm基础上实现一个 16bit数组的乘法累加的函数，并进行 -o2 / -o3 / 手工优化 2、c环境 C调用汇编函数，汇编函数调用c函数 addarr3(int * arr1, int * arr2, int * arr3, int * arr4, n) //汇编函数，3个数组的对应位置相加，结果放在arr4[n]中， 汇编函数调用C的子函数，它把arr1和arr2相加放到arr3[n]中； addarr2(int * arr1, int * arr2, int * arr3, n)-1, (1) 32bit multiplication instructions explained (2) the load.asm volume1 on the basis of a a 16bit multiplication cumulative array of functions, and-o2 /-o3/2 manual optimization, c environment compilation called C function, the compilation function call c function addarr3 (int* arr1. int* arr2, arr3 int*, int* arr4, n)// compilation function, 3 arrays corresponding location together, the results on arr4 [n], the compilation of the C function call function, arr1 put it together and put arr2 arr3 [n]; addarr2 (int* arr1, int* arr2, int* arr3, n)

In C Algorithms for Real-Time DSP, author Paul M. Embree presents a complete guide to digital signal processing techniques in the C programming language. This book is structured in such a way that it will be most useful to the engineer who is familiar with DSP and the C language, but who is not necessarily an expert in both. All of the example programs in this book have been tested using standard C compilers in the UNIX and MS-DOS programming environments. In addition, the examples have been compiled using the real-time programing tools of specific real-time embedded DSP microprocessors (Analog Devices ADSP-21020 and ADSP-21062 Texas Instruments TMS320C30 and TMS320C40 and AT&T DSP32C) and then tested with real-time hardware using real-world signals. -In C Algorithms for Real-Time DSP, author Paul M. Embree presents a complete guide to digital signal processing techniques in the C programming language. This book is structured in such a way that it will be most useful to the engineer wh

用matlab实现了二维离散余弦变换，内涵多个M文件，使用时请读者注意-Using matlab to achieve the two-dimensional discrete cosine transform, meaning more than M files, use the reader" s attention when you