这是一个简的电子屏幕，用于小型车间，能显示年，月，日。计划产量，实际产量都可以显示在板上。我用protus实现硬件仿真，并最终有实际成品出来。...

UCOS――FOR――UNSP2，ucos在凌阳单片机上的移植。-UCOS-- FOR-- UNSP2, Sunplus CENTER SCM in the transplant.

用VC实现的信号源界面代码，仅仅是界面，没有应用程序-To achieve a signal source with the VC interface code, just interface, there is no application

语音芯片ISD1420的C语言程序，实现简单的语音存储与播放。在KEIL下运行-ISD1420 voice chip of the C language procedures realize a simple voice storage and playback. Run in KEIL

这是我画的步进电机通用的驱动板，当然只是应用到初学者，版胡德不是很好，希望大家多多指教。-This is my painting of the stepper motor drive GM board, of course, only applied to the beginner, not a very good version of Ehud, I hope everyone exhibitions.

单片机,嵌入式系统实时操作系统rtos及基于80C51单片机源码 -Single chip, embedded systems and real-time operating system rtos source based on 80C51 microcontroller

这篇实验报告是关于单片机多路数据采集的，本实验由2大部分组成：1、为用EPOROM构成的心电信号发生器；2、为多路信号的微机采集与显示；第一部分实验主要研究可编程序存储器EPROM的非计算机应用。把存储在EPROM中的数字心电信号读出并通过D/A转换为模拟信号显示在示波器屏幕上。 第二部分实验的目的是研究一个数据采集系统，该系统利用ECD-51型单片机为中心，由D/A芯片等将各种低频信号以及由EPROM产生的模拟人体心电信号变换成离散的数字信号存入微机内存，以待进行数据处理和分析，然后再通过D/A转换将其还原成模拟信号显示在示波器的屏幕上。 -This experimental report on the multi-SCM data acquisition, the experiment by the two major components : 1. EPOROM pose for the use of the ECG signal generator; 2, multi-path signals in the computer acquisition and display; the first major study of experimental programmable EPROM memory in non-computer applications. Stored in the EPROM of ECG read out by D/A conversion of analog signals displayed on the oscilloscope screen on. Part II The purpose of this experiment is to study a data acquisition system, which uses ECD-51 microprocessor as the center, from the D/A chips, and other various low-frequency signal from EPROM and the simulation of human ECG transform into several discrete signal words into computer mem

用ATMEL AVR单片机开发的MMC程式在SPI模式-with ATMEL AVR development programs in the MMC SPI mode

232同485转换的pcb图，有需要的只要稍加修改一下就可以了-232 with 485 conversion pcb diagram, there is a need for as long as a little tinkering can be a

mcf5272的引脚比较多，设计原理图的时候比较复杂，可以用该的规范原理图，protel99se格式。-MCF5272 more of the pin, when the schematic design more complicated, can be used in the schematic diagram of the specification, protel99se format.

点阵LED显示0-9程序（c语言）,此程序为8*8LED点阵的简单程序-Dot-matrix LED display 0-9 program (c language)