24系列串行EEPROM的源代码，需要I2C总线的接口函数。

HE48R/E05A 实现I/O模式的工作原理-HE48R/E05A realize I/O model of principle

基于tw2835的的相关源代码程序，由一款51单片机来控制-Tw2835-based source code of the relevant procedures, by a single-chip microcomputer 51 to control the

msp430是ti公司的16位单片机，具有低功耗的特性，用在控制系统十分理想，是很有前途的单片机新品种，这是mps430-410单片机的调试程序-Controller is the 16-bit microcontroller with a low power consumption characteristics of the control system with a very good, very promising new varieties MCU, which is mps430-410 MCU debugger

对显示器LCD的读写和I2C的控制程序，供大家享用-Reading and writing on the LCD display and I2C control procedures for everyone to enjoy

自制51_AVR下载线[USB型]全套资料！相信对大家一定有用！-Home 51_AVR download cable [USB-type] full of information! I believe will be useful for everyone!

此程序为 单片机开发过程中，1―wire总线方式数字温度传感器的控制显示程序。供参考-procedure for microcontroller development process, 1-wire bus mode digital temperature sensor control display program. For reference

本设计主要是运用单片机设计一个最小系统――电子时钟，它具有24小时计时功能，能够对时间进行调整，并且能实现时、分、秒的显示，同时还有内设闹钟，时间到时候会响铃，响铃时可以通过按键控制延时再启动或关断。与此同时还设置了整点报时功能；并采用采用了软件去抖的方法扫描键盘，动态刷新显示数码管，并通过查表实现译码输出时间等编程方法；-This design is the use of single-chip design of a minimum system- Electronic clock, it has a 24-hour timer function, capable of time to adjust, and can achieve the hours, minutes and seconds display, but also equipped with alarm clocks, time to When ringing the bell to ring when the button control can delay re-start or shutdown. At the same time also set up the whole point timekeeping function and adopt the use of the software to scan the keyboard shaking method, dynamic refresh display digital tube, and through the realization of decoding look-up table output time programming method

不带汉字库的12864液晶程序，经过修改，可显示16*16汉字，8*8字符串，经过调试，可放心使用-without the LCD procedures 12864, as amended, will show that 16* 16 Chinese characters, 8* 8 strings, after debugging, can be assured use!

这是一个比较典型的PID处理程序，在使用单片机作为控制cpu时，请稍作简化，具体的PID 参数必须由具体对象通过实验确定。由于单片机的处理速度和ram资源的限制，一般不采用浮点数运算，而将所有参数全部用整数，运算 到最后再除以一个2的N次方数据（相当于移位），作类似定点数运算，可大大提高运算速度，根据控制精度的不同要求，当精度要求很 高时，注意保留移位引起的“余数”，做好余数补偿。这个程序只是一般常用pid算法的基本架构，没有包含输入输出处理部分。-This is a typical PID process, as in the use of SCM control cpu, please slightly simplified, specific PID parameters to be specific targets identified by experiments. As SCM processing speed and ram resource constraints, generally do not use floating-point operations, and will use all the parameters of all integers, and the final calculations to divide one of the Nth 2 data (the equivalent displacement), will count for a similar operation, it will greatly increase the computing speed, control Accuracy of different requirements and high precision, displacement caused reservations to the attention of the "I", which I do several compensation. This procedure is commonly used algorithm pid the basic structure does not include input and output processing.

MCS-51单片机教程 MCS-51单片机教程-MCS-51 microcontroller Guide MCS-51 microcontroller MCS Guide-51 SCM Guide MCS-51 microcontroller Guide