51单片机模拟解码2272程序，此方法较硬件解码要方便而且灵活性要强，可靠性也得到加强。...

自行车里程设计的远程序 他的用途很实际的 并且说明详细-bicycle mileage from the design process he uses a very practical and detailed note

mifare 232读卡源程序用kei uvision打开-MIFARE reader source with open Kei uvision

采用UART方式0与LM74通信。 用C8051f020的P0.7作片选，主机通过TXD发送时钟信号，实现同步通信,半双工.RXD 作双向数据线.用六位数码管显示LM74采集的温度值-The use of UART communication mode 0 and LM74. P0.7 used for the C8051F020 chip select, host TXD sent through the clock signal, to achieve synchronous communication, half-duplex. RXD for bi-directional data line. With six digital tube display LM74 temperature collected

tda7313音调处理系统.全遥控带,控键,液晶显示.电话13580588450-tda7313 tone processing system. Full remote control zone, control keys, LCD. Tel 13580588450

方波产生程序 megal128 iccavr开发平台 -Square wave generation process development platform megal128 iccavr

用8051汇编编程的定点，三字节浮点，四字节浮点的字程序库。-8051 compilation of programming with the fixed-point, three-byte floating-point, four-byte floating-point library word.

使用c51单片机制作的气象五要素采集程序 包括DS1302温度以及TLC2543、24c04，键盘 240*320液晶模块！-use c51 SCM produced five elements of the meteorological collection procedures include DS1302 temperature and TLC2 543,24 c04, keyboard 240* 320 LCD module!

采样C语言编写的128×64分辩率的汉字液晶显示驱动程序-C language sampling of 128 x 64 Resolution of the Chinese LCD Driver

1．熟悉硬件仿真工具KD30的使用。 2．修改样本程序 SAMP1a，使无论在计数或停止计数时，按 SW3 均对计数值清零，并停止计数。 3．编制一个秒表程序, 测试精度为0.1秒，按 SW1键启动计数，再按一次 SW1键停止计数。任何时候按 SW3 键停止计数，并对计数值清零。 4．按 SW1键后， 以 0.1 秒为单位开始计数，再按一次 SW1 键停止计数。若按 SW1 键时间超过2秒，则计数值清零，回到初始状态。-1. Familiar with the hardware simulation tool KD30 use. 2. Revised procedures SAMP1a samples, regardless of the count or counts at the end, according to SW3 numerical terms were right, reset, and stop counting. 3. Preparation of a stopwatch procedures, testing accuracy of 0.1 seconds, according to bond SW1 start counting, according to a key SW1 stopped counting. By SW3 any time to stop counting bond and reset the count. 4. By SW1 bond, after 0.1 seconds for start counting, according to a key SW1 stopped counting. If SW1 keys by the time more than two seconds, then reset the count and return to the initial state.

MSP430 PS/2键盘接口程序 LCD1602显示。 程序包含对PS/2键盘发送数据的处理，以及如何通过查找表显示所收到的数据，并通过显示缓存显示到1602液晶上。-MSP430 PS/2 keyboard interface program LCD1602 display. Process consists of PS/2 keyboard to send data treatment, as well as how to find table shows the data received and, through the display buffer on the LCD display to 1602.