cold light source products controller HT48R series and HT48E Series

基于MC68HC908RF2芯片轮胎压力监测系统的发射程序，采用曼彻斯特编码，FSK，9600bps-MC68HC908RF2 chip-based tire pressure monitoring system for the launch procedures, the use of Manchester encoding, FSK, 9600bps

功能强大的51编程器，文件包里有PC机程序、编程程序和硬件电路。-powerful 51 programmer, a paper bag of PC and programming procedures and hardware circuit.

这是一个ht1620的资料，希望对你有用-This is a ht1620 information useful to you hope

ds18b20 温度传感器 硬件设计和软件编程 供大家学习只用 能力有限 大家共同探讨-DS18B20 temperature sensor hardware design and software programming for your learning only limited ability to explore all

可进行不同数组联系起来的16位crc的校验.内部含有中文说明,并且已经测试过,完全正确.就是自己平时进行应用的程序.-Can be linked to a different array of 16-bit CRC checksum. Internal note containing Chinese and have been tested, absolutely correct. Is usually carried out its own application procedures.

单片机RS232/RS485串行发送实验（双机通讯）。 实验步骤： （1），准备两台598K实验机，确定1号机为发送，2号机为接收； （2），当作RS232接口实验时，1号机和2号机的P3.0和P3.1交叉相连，且两机共地； （3），当作RS485接口实验时，1号机和2号机的A、B作对应连接，同时1,2号机的R/TEN接P1.0, P3.0接R0, P3.1接DI。 （4），先运行2号机，键入[27]-->[EV]使2号机处于接收状态P。，后运行1号机[26]-->[EV]使1号机处于发送状态,P。会闪烁，在1号机键盘上按动数字键，在2号机的数码管上应显示对应的数字键值。-Send Singlechip RS232/RS485 serial experiment (two-plane communications). Experimental steps: (1), prepare two sets of experiments 598K machine, determined on the 1st machine to send, on the 2nd machine to receive (2), as a RS232 interface experiment, on the 1st and the 2nd machine and P3.0 P3.1 cross-linked, and the two planes were to (3), as a RS485 interface experiment, on the 1st and the 2nd machine A, B for the corresponding connection, while 1,2 No. of R/TEN then P1 .0, P3.0 access R0, P3.1 then DI. (4), first run on the 2nd machine, type [27]

MCS-51单片机实用子程序库,包括全套的数据转换与计算的子程序。-MCS-51 microcontroller practical subroutine library, including a full set of data conversion and calculation of the subroutine.

AVR 4通道AD转换程序 采用连续自由转换方式工作 希望对大家有帮助-AVR 4-channel AD conversion process continuous conversion mode free work hope to have everyone help

AVR单片机应用系统开发典型实例_4 -AVR Singlechip classic example of application systems development _4

这是VB编程RS232串口（COM口）控制的D/A(数模转换)转换板的上位机演示程序。通过电脑串口（或其他具有串口的单片机、PLC、DSP）发个简单的可视ASCII指令，便可以方便地控制8个数模转换通道输出设定的电压值。比如,电脑串口输出字符串"C2V2660"到本控制板,则控制板将控制2号通道输出2.66V电压；电脑串口输出字符串"C6V3060"到本控制板,则控制板将控制6号通道输出3.06V电压.指令非常简单，完全不需了解复杂的硬件及时序控制。-This is a VB programming RS232 serial port (COM port) control D/A (digital-analog conversion) conversion board host computer demonstration program. Via the computer serial port (or other serial port of the microcontroller, PLC, DSP) made a simple visual ASCII commands, they can easily control the number of eight-channel DAC output set voltage. For example, the computer serial output string " C2V2660" to this control panel, then the control board will control 2-channel output 2.66V voltage computer serial output string " C6V3060" to this control panel, then the control board will control the 6 channel output voltage is 3.06V. instruction is very simple, completely without understanding of complex hardware and timing control.