1总线通信协议应用实例 (C51编写的源程序,keil)

cpu采用扫描方式进行按键查询，按键扫描程序-cpu manner by scanning button inquiries button scanner

ATmega8+315M或433.92M的超再生接收头+1602六线控制的1602显示解到的码-ATmega8+ 315M or 433.92M the超再生receive the first+ 1602 six-lane controlled display solutions to the 1602 Code

//115.2k串行口通信程序，校验方式为简单双向校验, //而且是必要的，因为任何采用中断、crc等的方法 //均很难保证速度和避免错误. //总体速度5KB/秒 //单片机程序 //使用22.1184晶振-//115.2k serial port communication procedures and testing methods for the simple two-way check,// it is necessary, because any interruption used, the method crc// it is very difficult to ensure speed and avoid mistakes.// Overall speed 5KB/s// MCU procedures// crystal use 22.1184

MSP430-LCD1602液晶显示驱动程序，MSP430-LCD1602液晶显示驱动程序-MSP430-LCD1602 LCD driver, MSP430-LCD1602 LCD driver

PIC1687X单片机,LCD12232汉显,所有数据存于片内FLAISH中,断电保持,硬件调试通过-PIC1687X microcontroller, a LCD12232 Han, All data stored in chip FLAISH, maintain power outages, hardware debugging through

应用C51单片机控制的数字时钟显示程序,显示模块采用了简单易行的数码管-application C51 microcontroller control of the digital clock display program shows that the modules use a simple digital control

5615的使用,即TLC5615头文件,谢谢各位下载啊-The use of 5615, that is, header files TLC5615 Thank you to download ah

本程序用于MICROCHIP 24LC64 EEPROM的读写。本程序不使用芯片级联方式， 请将A0，A1，A2 管脚接至低电平。本程序使用IOC6作为SDA，IOC7作为SCL。 程序中的地址空间最大可至64K：24LC00-16-0，24LC01-128-8，24LC02-256-8， 24LC04-512-16，24LC08-1K-16，24LC16-2K-32，24LC32-4K-32，24LC64-8K-32， 24LC128-16K-64，24LC256-32K-64，24LC512-64K-128，读写数据均为8bits。 以上器件的格式为（型号-地址空间-页大小）不同器件的页大小不同，因此页写 程序需作相应修改，其他字节写，随机读以及顺序读程序均相同-This procedure for the MICROCHIP 24LC64 EEPROM read and write. This procedure does not use chips cascade way, please A0, A1, A2 pin to low level access. This procedure used IOC6 as SDA, IOC7 as SCL. Process address space available to the largest 64K: 24LC00-16-0, 24LC01-128-8, 24LC02-256-8, 24LC04-512-16, 24LC08-1K-16, 24LC16-2K-32, 24LC32-4K- 32,24 LC64-8K-32, 24LC128-16K-64, 24LC256-32K-64, 24LC512-64K-128, read and write data are 8bits. The format for the above device (Model- address space- page size) of different devices of different sizes of pages, so page written procedures need to be amended accordingly, and other bytes to write, rand

使用的是arm单片机LPC2210，进行AD 转换，使用ADC模块进行电压测量，有多个程序模块-use of the arm LPC2210 MCU for AD conversion, ADC module for use voltage measurement, there are a number of program modules

程序的地址译码，单片机系统中做为外扩接口的地址译码。-Procedures address decoder, microcontroller system as a foreign expansion of the address decoder interface.