DSP ADC 例子 DSP 2812 ADC 例子

程序是对16位dsp的cmd文件标准配置，dsp cmd文件是dsp程序是否能够稳定运行的条件-Program is 16-bit dsp standard configuration of the cmd files, dsp cmd file is dsp procedures to stabilize the conditions of operation

CCS C sample for a timer,using the timer1 to produce the interrupt routine-the timer can be used for all kinds of the usage, for example,indutrial..

编解码器方案是编码和 decodding 的声音 dsk kit.input 可以从声音或行中的作为电气 signal.voice 信号从麦克风给 dsk 工具包通过麦克风在引脚。这一方案是 dsk6713 工具包但还可以做其他 dsk 工具包。在把信号编码组件上，你可以 listean 它从 headphon 或扬声器。

1、（1）32bit乘法的指令解释 （2）volume1的load.asm基础上实现一个 16bit数组的乘法累加的函数，并进行 -o2 / -o3 / 手工优化 2、c环境 C调用汇编函数，汇编函数调用c函数 addarr3(int * arr1, int * arr2, int * arr3, int * arr4, n) //汇编函数，3个数组的对应位置相加，结果放在arr4[n]中， 汇编函数调用C的子函数，它把arr1和arr2相加放到arr3[n]中； addarr2(int * arr1, int * arr2, int * arr3, n)-1, (1) 32bit multiplication instructions explained (2) the load.asm volume1 on the basis of a a 16bit multiplication cumulative array of functions, and-o2 /-o3/2 manual optimization, c environment compilation called C function, the compilation function call c function addarr3 (int* arr1. int* arr2, arr3 int*, int* arr4, n)// compilation function, 3 arrays corresponding location together, the results on arr4 [n], the compilation of the C function call function, arr1 put it together and put arr2 arr3 [n]; addarr2 (int* arr1, int* arr2, int* arr3, n)

用dsp解压mp3程序的算法，感觉很好，很有用，可以-with dsp decompression procedures MP3 algorithm, feel good, useful and can s

5个源程序都是在VisualDSP环境下开发出来的，目标处理器是4片AD公司的TS1O1 DSP。其中：1）IDE_FAT32用来在硬盘上创建FAT32文件系统；2）i2c_test编写IIC总线；3）codec_a_in_pal_cf_frame是加载到FLASH的程序，板子在脱离PC自动上电时会把PAL制的图像直接存到CF卡里，CF卡的文件系统是FAT16；4）codec_a_in_pal_buf_boottest是可加载的DSP图像直通程序；5）ADSP-TS101prog_driver是flash的驱动程序。-five VisualDSP source in the environment are developed under the target processor is four AD TS1O1 the DSP. Of which : a) IDE_FAT32 used in the drive to create FAT32 file system; 2) to prepare i2c_test IIC bus; 3) codec_a_in_pal_cf_frame FLASH is loading procedures, the board automatically from the PC on when power will be PAL system images directly to CF card, the CF card is the FAT16 file system; 4) can be loaded codec_a_in_pal_buf_boottest DSP image through procedures; 5) ADSP-TS101prog_driver flash is the driver.

一些TI的DSP2047上的我写的程序，供大家参考，还请大家帮忙改正错误．-some of the DSP2047 I wrote the procedure, for your reference, please help to correct the mistake.

c语言编制的存储器dsp实验测试程序，可在ccs下运行-memory dsp experimental procedure can run in ccs

CCS环境下，四相编码脉冲压缩雷达算法研究（包含整个项目）-CCS 拢 压

5402 ExInt源程序，都可以用，通过仿真的-5402 ExInt source, can be used, through simulation