程序资料共享 希望大家共同进步 共同努力 加油 ！

C源程序开发，关于液晶显示的C程序编写，可以作为参考 -C source development, LCD on the C programming can be used as reference

介绍了用RS-232串口进行开发的过程，对于刚涉及串口编程的开发人员有一定帮助-Introduction by RS-232 serial port to carry out development process, for serial programming just related to the development of staff has a certain extent, help

一种基于单片机系统的多级菜单模块化编程．方便了菜单的加载与卸载,软件结构清晰,维护方便-SCM systems based on multi-level menus modular programming. To facilitate the loading and unloading of the menu, software, clear structure and easy maintenance

美国TI公司的protel 元器件库，在应用中需要更新，本人收集了最新的版本共30M，为提高上传速度分六次上传。文件名依次为TI_1到TI_6。希望大家设计电路板时少走弯路 以下是TI_5-TI" s U.S. Treasury protel components, need to be updated in the application, I collected a total of up-to-date version of 30M, to improve the upload speed upload six hours. File name followed by TI_1 to TI_6. Hope that the design of circuit board is less detours following TI_5

汇编语言，用定时器中断，实现输出占空1比1的方波波形-Assembly language, using the timer interrupt, the realization of output accounted for one than the one empty square waveform

仿真步骤如下： 1、把3个帖子的内容分别保存为51t9py.c,51t9py_indexa.h,5py_mb.h，放在同一目录下，将51t9py.c加入工程编译 2、由于Keil的模拟串口是单字节显示，汉字显示为乱码，所以要加挂RICHWIN或RichView这种会重新刷新显示的中文平台，或手工刷新屏幕，所以请先到 http://www.pchome.net/dl/chinese.htm 下载RichView，安装运行 3、在Keil环境下可以直接按“Ctrl＋F5”键仿真，按“F5”全速运行，切换到在串口依次输入: // 64*.6 426***.5 98*.7 936.3 586.1 4826*.1 9464*.7 64*.6试试:-) 4、按键对应(根据我自己的手机设置的,全部在PC的小键盘操作)： -simulation steps are as follows : 1 and 3 respectively, the content of messages posted on the preservation of 51t9py.c, 51t9py_indexa.h, 5py_mb.h, on the same directory, will join the project 51t9py.c compiler 2, Keil is the simulation of single-byte Serial show , the Chinese showed gibberish, so need to add or RichView RICHWIN this show will re-set the Chinese platform, or manual refresh screen, so please download RichView http://www.pchome.net/dl/chinese.htm to install three operations in Central Keil Habitat can be directly "Ctrl+ F5" key simulation, according to the "F5" running full-speed, switched to the ser

基于320×240图形点阵液晶与51单片机的接口设计程序。采用C51编程制作。-Based on 320 × 240 dot-matrix graphic LCD interface with 51 single-chip design process. The use of C51 produced programming.

AVR MCU 用于AVR单片机采集模拟信号-AVR MCU for analog signal acquisition AVR Singlechip

LCM 12864 LCD图形显示程序例子 在LCD上显示一幅图，是“我的电脑，我的文档”。IC用PIC16F877A，晶振 4MHZ，采用并行8线，LCD：TS12864-3，接法在程序中有定义，只要将此程序COPY到你的PICC里编译下载后，在目标板上即可以看到图画了！-LCM 12864 LCD graphics display program examples in the LCD display a map, is the

LPC2119的CAN驱动程序,开发环境问ads1.2-LPC2119