用汇编语言实现数据采集,数据显示,数据通信(2543,7279等芯片),是我做的毕设题目...

6段数码管分别显示，时，分，秒，四个按键，K1（P0.0），K2（P0.1）， K3（P0.2），K4（P0.3），四个按键用来调时间的，按下K1，所有位都清零显示，然后按下K2，秒在闪烁，继续按K2分闪烁，不段地按K2 秒--分--时切换着闪烁，在某位闪时按下K3相应位加一，确认调整，按K4，取消调整再按K1。在K1按下以后才有调时的功能，如果K1没有按下，按别的键没有反映。这为了在加点按键功能留着用 -6 respectively of the digital control, when, minutes and seconds, four keys, K1 (P0.0). K2 (P0.1), K3 (P0.2), K4 (width), the four keys to the transfer time, press the K1, All spaces are reset, then press K2, the scintillation seconds, according to K2 pm flickered. not according to K2 of seconds-- minutes-- when switching to flicker in certain press the flash-K3 corresponding increase in a confirmed adjustment by K4, then canceled K1 adjustment. K1 in the press will only be made after the transfer of function, if K1 pressed by other key is not reflected. This points to the function keys used Retention

绘制LCD的RGB和喷墨打印机的 CMYK到CIELab的三维彩色视图 -LCD rendering of RGB and CMYK inkjet printers to the CIELAB color three-dimensional view

单相电机变频驱动原码,采用DISPIC30芯片-Single-phase motor inverter drive the original code, the use of chip DISPIC30

利用单片机控制实现的计算器，用lcd显示计算的过程和结果。-SCM control to achieve use of calculator, lcd display with the calculation process and results.

51单片机串口数据包收发程序，能一次收发多个字节，可跟据需要自行修改字节长度，并且具有接收超时判断功能。-51 Single-chip serial data packets to send and receive procedures, can send and receive more than one byte can be modified according to the needs of self-byte length, and have to receive overtime to determine function.

FlashAcessV0.4.6版，用于烧写FALSH的应用程序，需要BANYAN DAEMON的支持，配合BNAYAN系列仿真器或者简易JTAG电缆访问目标板上的FLASH，可支持ARM7/ARM9，各种FLASH。需要1K RAM 运行-FlashAcessV0.4.6 version for the application programmer FALSH, BANYAN DAEMON need the support and facilitation of BNAYAN series or simple JTAG emulator target cable access board FLASH, can support ARM7/ARM9, a variety of FLASH. 1K RAM needs to run

利用单片机加控制直流电机，利用P1口，编制程序输出一串脉冲，经放大后驱动小电机，改变输出脉冲的电平及持续时间，达到使电机正转、反转、加速、减速。停转之目的。 可以通过74LS244输入开关量数据来控制小直流电机的转动，实现正转四种转速，反转四种转速及停转。 -The use of SCM in controlling the DC motor

这是一个实现串口通讯,发送与接收的源程序。用最简单的方法进行串口调试-This is a Serial communication, send and receive the source code. The simplest way to use serial port for debugging

LT-1B开发板例子程序－ADC12_05

LM128*64液晶驱动程序，有显示图形，汉字，画线等功能 -LM128* 64 LCD driver, has display graphics, characters, painting lines and other functions