红外ICCAVR下的译码程序，包括所有源代码，以及…

利用51系列单片机实现四种波形，正弦波、方拨、阶梯波、三角波，采用开关电路实现四种波形转换、放大电路实现波形幅度可调。通过编程实现仿真。-51 Series MCU realize the use of four types of waveforms, sine, square dial, ladder wave, triangle wave, the use of switching circuits to achieve the four waveform conversion, amplifier circuit realize adjustable waveform amplitude. Through the realization of simulation programming.

8155做的电子时钟，对学单片机的人有很大帮助-8155 to do electronic clock, on the school single-chip microcomputer has a lot to help people

这是一个接收单片机数据的软件,通过对接收的数据分析来显示相应的LED.目前只能显示一个LED,有时间会全部做好的,目前接收到的数据为0A0B0C,也就是从单片机发出来的数据为10,11,12,单片机的程序是a-This is a single-chip microcomputer software to receive, through the analysis of data received to display the corresponding LED. Currently only display a LED, will all have time to do a good job of currently received data 0A0B0C, that is, from a single machine sent to the data for 10,11,12, SCM process is a

利用单片机以及DA0832产生正弦波的C51源程序-As well as the use of single-chip generated sine wave DA0832 source of C51

这是通讯接口实验《DA转换原理实验》的原理程序，适合于那些上嵌入式系统、通信、计算机专业的人-This is the communication interface experiment, "DA conversion principle experiment," the principle procedures, suitable for those on embedded systems, communications, computer specialists in the

基于MSP430F169的TS12864-5程序 可以显示汉字，字符，以及反白显示-Based on the MSP430F169 of TS12864-5 program can display Chinese characters, characters, and anti-white display

=== =时钟20:6=== === == 应先初始化状态寄存器 tx1714 EQU 7FFH PA EQU 05H PB EQU 06H PC EQU 07H PD EQU 20H IAR EQU 00H 间接寻址寄存器 TMR0 EQU 01H 定时器 STATUS EQU 03H 状态寄存器 BSR EQU 04H bank选择寄存器 PORTA EQU 05H I/0端口寄存器 PORTB EQU 06H I/0端口寄存器 PORTC EQU 07H I/0端口寄存器 PORTD EQU 20H I/0端口寄存器 PULL EQU 21H PULL-High上拉寄存器 WAKEUP EQU 22H 唤醒控制寄存器－－被用来设定watchdog允许和禁止 IRQM EQU 23H 中断屏蔽寄存器 IRQF EQU 24H 中断标志寄存器 WDTSEL EQU 25H -=== === = clock 20 : 6 === === === == should first register initialization state tx1714 EQU 7FFH EQU PA PB EQU 05H 06H 07H PC EQU PD EQU 20H IAR E QU 00H indirectly addressable registers TMR0 EQU 01H timer STATUS EQU Mr send state BSR EQU-deposit bank in the 04H choice Register PORTA EQU 05H I/O ports Register P ORTB EQU 06H I/O ports Register PORTC EQU 07H I/O ports Register POR TD EQU 20H I/O ports Register PULL EQU 21H PULL-High pull Register WAKEUP EQU 22H awaken control registers-- were used to set watchdog allowed and prohi

MSP430有许多寄存器来设定程序的频率和周期，本文总结如定时器A,看门狗，模拟比较器等的代码，供大家参考学习.-MSP430 has a number of registers to set the procedures for the frequency and cycle, such as This paper summarizes the timer A, watchdog, analog comparator, such as the code for your learning.

三相步进电机的三相六拍工作方式，正转的绕组通电顺序：A、AB、B、BC、C、CA、A，反转的通电顺序：A、AC、C、CB、B、BA、B、A。 由于步进电机转子有一定的惯性以及所带负载的惯性，故步进电机的工作过程中不能及时的启动和停止，在启动时应慢慢的加速到预定速度，在停止前应逐渐减速到停止，否则，将产生失步现象。 步进电机的控制问题可总结为两点： 1、产生工作方式需要的时序脉冲； 2、控制步进电机的速度，使它始终遵循加速、匀速、减速的规律工作。 -Three-phase three-phase stepper motor six shot work, is to order the winding power: A, AB, B, BC, C, CA, A, reverse the order of power: A, AC, C, CB, B, BA, B, A. As the stepper motor rotor has a certain degree of inertia, as well as brought about by the inertia load, the stepper motor during the course of work should not start and stop time, start to be slowly accelerated to a predetermined speed, the stop should be to slow down gradually to the stop, otherwise, will result in out-of-step phenomenon. Stepper motor control problems can be summarized in two points: one, resulting in the need to work the timing pulse 2, control the speed of stepper motor, so that it always followed acceleration, velocity, deceleration of the law of the work.

128*64点 LCD及DS1302 应用-128* 64 points, LCD and DS1302 Application