深入理解内存原理，有助于嵌入式工程师硬件开发。

实现cpld和pc机之间的串口通信，PC机传送到CPLD的信息，CPLD传回到PC机-Via verilog language ，cpld can communcate with pc.

24c01-24c16读写驱动程序-24c01- 24c16 literacy Driver

Altera recommends the following system configuration: * Pentium II 400 with 512-MB system memory (faster systems give better software performance) * SVGA monitor * CD-ROM drive * One or more of the following I/O ports: - USB port (if using Windows XP or Windows 2000) for USB-Blaster(TM) or MasterBlaster(TM) communications cables, or APU programming unit - Parallel port for ByteBlasterMV(TM) or ByteBlaster(TM) II download cables - Serial port for MasterBlaster communications cable * TCP/IP networking protocol installed * Windows 2000, Windows NT 4.0 with Service Pack 3 or later, or Windows XP * Internet Explorer 5.0 or later Memory & Disk Space Requirements USB开发--Altera recommends the following system configuration:* Pentium II 400 with 512-MB system memory (faster systems give better software performance)* SVGA monitor* CD-ROM drive* One or more of the following I/O ports:- USB port (if using Windows XP or Windows 2000) for USB-Blaster(TM) or MasterBlaster(TM) communications cables, o

详细介绍了FAT文件系统（包括FAT12,FAT16,FAT32），不知是哪位牛人写的电子书，非常经典，多亏了它，我才完成了FAT文件系统在ARM上的实现-Detailed the FAT file system (including FAT12, FAT16, FAT32), I do not know which cattle were written e-books, very classic, thanks to it, I finally completed the FAT file system on the ARM realize

这个是比较详尽的飞利浦lpc22xx系列的资料，相对于lpc其他较少的资料而言，这个pdf还是比较全面的！-This is more detailed information on Philips lpc22xx series, as opposed to other less lpc information, this pdf is quite comprehensive!

jxta最新版本v2.3.X的程序编写指南-JXTA v2.3.X latest version of the guidelines for the preparation of procedures

基于单片机与ch451的键盘扫描与显示程序-Based on SCM and ch451 keyboard scanning and display program

操作系统为wince,开发环境为EVC,有关PING的应用程序-operating system and development environment for EVC, the PING applications

eVB调用从一个DLL中写入eVC文件，达到控制程序录音要求的使用

提供的程序是供四相步进电机使用。本实验使用的步进电机用直流+12V电压，电机线圈由A、B、C、D四相组成。 2. 驱动方式为四相单四拍方式,各线圈通电顺序如下表。表中首先向A相线圈输入驱动电流，接着向B，C，D线圈通电，最后又返回到A相线圈驱动，按这种顺序轮流切换，电机轴按顺时针方向旋转。若通电顺序相反，则电机轴按逆时针方向旋转。-provide for the procedures of the four-phase stepper motor use. This experiment used the stepper motor 12V DC voltage electrical coils A, B, C, D phase. 2. Four-driven approach to making four single-phase, the coil electrifying sequence the following table. Table A first phase coil input drive current, then to B, C, D coil electricity and eventually return to the A-phase coil driven by the rotation order of this switch, the electrical axis by rotating clockwise direction. If electricity in reverse order, the motor shaft by the anti-clockwise rotation.