仔细详细的介绍了msp430单片机的各个寄存器，对初学者相当的有用...

基于中断控制的声光报警器的设计.采用中断方式，设计一个声光报警器的硬件电路和控制程序。程序运行时，一旦8位开关信号量状态满足设定条件，就触发中断，使发光二级管按规律闪烁，同时扬声器播放一段音乐。 硬件设备包括一台微机、一个MFID微机实验箱、一块T型板，2输入四与门 74ls08、8位总线驱动器 74ls245、LM386A音频放大器、排阻、扬声器各一个，发光二极管8个，470uF电容2个、104电容4个，插线若干。 -Interrupt-based control of sound and light alarm design. Using interrupt mode, designing a sound and light alarm hardware circuits and control procedures. The program is running, once the 8-bit switch signal to set the amount of state to meet the conditions to trigger interrupts, so that light-emitting diode flashes according to the law, while speakers play a piece of music. Hardware includes a computer, a computer simulation, MFID box, a T plate, 2 input 4 and gate 74ls08, 8-bit bus driver 74ls245, LM386A audio amplifier, exclusion, speakers of a light-emitting diode 8, 470uF capacitor 2 a, 104 capacitors 4, plug-line number.

爱普生S1C33L05 s USB驱动程序库

这程序是实现单片机与PC机的通信程序 可供大家参考或学习！-MCU and PC communication program for reference or study!

MC9S12DG128B，包含了时间中断、光电检测、舵机控制、电机驱动、实时控制等功能。有相关注释。-MC9S12DG128B, includes a time interrupted, photoelectric detection, steering control, motor-driven, real-time control functions. Relevant Notes.

单片机应用源码,包括各种简单操作，同时还有大型应用，例如IC卡读写，多机通信等-SCM application source code, including all simple to operate, but also to large-scale applications, such as IC card reader. Multi-machine communication

这是一个接收单片机数据的软件,通过对接收的数据分析来显示相应的LED.目前只能显示一个LED,有时间会全部做好的,目前接收到的数据为0A0B0C,也就是从单片机发出来的数据为10,11,12,单片机的程序是a-This is a single-chip microcomputer software to receive, through the analysis of data received to display the corresponding LED. Currently only display a LED, will all have time to do a good job of currently received data 0A0B0C, that is, from a single machine sent to the data for 10,11,12, SCM process is a

ch451键盘LED管理芯片的驱动程序,很好用的,设计很标准的代码-ch451 keyboard LED chip management of the driver, the good design is the standard code

基于Keil C平台的源程序，是针对AT89ls52的4×4键盘扫描程序，采用查询方式进行-Keil C based on the source platform is AT89ls52 for the 4 × 4 keyboard scanning procedures, the use of inquiries conducted

该程序用于使CCP1模块产生分辨率为10位的PWM波形，占空比为50 */-该程序用于使CCP1模块产生分辨率为10位的PWM波形，占空比为50*/

是一款不错的单片机开发软件说明,开发单片机前的必备知识学习。-Is a good description of single-chip microcomputer software, the development of single-chip pre-requisite knowledge.