自己写的1621驱动程序（绝对可以用的，针对NEC单片机的）

usb开发工具周立功公司下载很好用的一个软件-development tools usb Ligong weeks to download a very good company with a software

在MSP430单片机上用C操作MMC和SD卡的电路和参考代码。含PDF文档。-MSP430 single chip microcomputer used in the C operator MMC and SD cards circuit and reference code. Containing PDF documents.

小功率LED条形灯的全彩控制含64阶灰度变化，可供学习LED控制的朋友参考。-Low-power LED light bar control with full-color 64-band gray-scale changes, for studying the control of Friend LED reference.

单片机中用c语言编写的实现不同点亮方式的流水灯程序-Single-chip using c language different water lamps lit the way procedures

本系统参照片上系统的设计架构、采用FPGA与SPCE061A相结合的方法，以SPCE061A单片机为进程控制和任务调度核心；FPGA做为外围扩展，内部自建系统总线，地址译码采用全译码方式。FPGA内部建有DDS控制器，单片机通过系统总线向规定的存储单元中送入正弦表；然后DDS控制器以设定的频率，自动循环扫描，生成高精度，高稳定的5Hz基准测量信号。-The system with reference to the design of system-on-chip architecture, used a combination of FPGA and SPCE061A approach to SPCE061A Singlechip for process control and scheduling core mission FPGA for external expansion, internal self-system bus, address decoding using the entire translated code approach. DDS has built internal FPGA controller, microcontroller through the system bus to the provisions of the storage unit into the sine table DDS controller and then to set the frequency, automatic cycle of scanning, to generate high precision and high stability of the baseline measurement 5Hz signal.

基于51单片机的公交车报站系统程序 基于51单片机的公交车报站系统程序-Based on 51 MCU bus stop announcement system program

程序匠人的一片有关于按键的文章，十分经典，按键的规划，分类,"长按"“短按”-Program artisans an article on the button is very classic, key planning, classification, " long press" " Short Press" and so on

1．熟悉硬件仿真工具KD30的使用。 2．修改样本程序 SAMP1a，使无论在计数或停止计数时，按 SW3 均对计数值清零，并停止计数。 3．编制一个秒表程序, 测试精度为0.1秒，按 SW1键启动计数，再按一次 SW1键停止计数。任何时候按 SW3 键停止计数，并对计数值清零。 4．按 SW1键后， 以 0.1 秒为单位开始计数，再按一次 SW1 键停止计数。若按 SW1 键时间超过2秒，则计数值清零，回到初始状态。-1. Familiar with the hardware simulation tool KD30 use. 2. Revised procedures SAMP1a samples, regardless of the count or counts at the end, according to SW3 numerical terms were right, reset, and stop counting. 3. Preparation of a stopwatch procedures, testing accuracy of 0.1 seconds, according to bond SW1 start counting, according to a key SW1 stopped counting. By SW3 any time to stop counting bond and reset the count. 4. By SW1 bond, after 0.1 seconds for start counting, according to a key SW1 stopped counting. If SW1 keys by the time more than two seconds, then reset the count and return to the initial state.

9851基本的操作，pic16f628希望对初学者有用！嘻嘻！-9851 basic operation, pic16f628 hope useful for beginners! Hee hee!

keil51使用中文详解-keil51 Comments on the use of Chinese