51单片机编写制做的电子计算器（韩国）汇编语言、C语言

用单片机控制1062显示温度--精确到0.0625度，汇编语言。-1062 using single-chip temperature control accurate to 0.0625 degrees, assembly language.

调试通过了的基于89S51的LCD12864液晶显示-Debugging based on the adoption of the 89S51 LCD LCD12864

一种汇编的16F877控制595的LED屏源程序-16F877 to control a compilation of 595 of the LED screen source

本系统以AT89S52单片机为核心部件，外加温度采集电路、及显示电路和越限报警等电路。采用单总线型数字式的温度传感器DS18B20，使系统具有测温误差小、分辨率高、抗干扰能力强，动态显示的方式等特点。本设计既可以对当前温度进行检测又可以对温度进行数码显示，两位整数两位小数的显示方式具有更高的显示精度，若超越极限温度则触发蜂鸣器报警。利用功能强大的Keil和具有互动电路仿真的Proteus进行程序的编写和仿真。-The system AT89S52 microcontroller as its core components, plus the temperature acquisition circuit, and display circuitry, and the more limited alarm circuits. Single bus-type digital temperature sensor DS18B20, the system has a temperature measurement error of the small, high resolution, anti-interference ability, dynamic show the way and so on. This design not only can detect the current temperature can also right temperature digital display, two integers with two decimal places are displayed to show a higher precision, if the temperature is beyond the limits of buzzer alarm is triggered. Keil and the use of powerful interactive circuit simulation of the Proteus programming the preparation and simulation.

用Win32Asm语言编写，计算1901-2050的农历、节气数据。-Win32Asm languages used to calculate the 1901-2050 Lunar, Solar data.

该程序实现显示一个数字的方阵，程序中的清屏功能可将上次运行的结果 清除，重新显示下次运行结果。本程序在dos中或windows98中运行。-the program figures show a phalanx, procedures of the screen will be the last operation to remove a result, the next re-running show results. This procedure dos or running Windows98.

带界面的两位数计算器，完成加减乘除运算欢迎使用-calculator

通用键盘显示程序，可连接带有isp接口的嵌入主板-Universal Keyboard Viewer, can be connected with the isp interface embedded motherboard

一个牛顿插值的matlab的m文件-A Newton interpolation matlab m-file

设计一种自动洗衣机的程序控制器，在启动后先进水，等到达高水位后，启动洗衣马达转动4min，如在洗衣过程中发现水位低于高水位，则停止洗衣马达转动并报警，并在水位到达高水位后再次启动马达。洗衣结束后则启动排水开关，待水位到达低水位后，则启动脱水马达，转动2min。如此重复三次，要求在每一动作之间有2s的间隔。 高水位，低水位为水位传感器，用两个开关模拟，当水位高于高水位或低于低水位时，两个开关的状态分别为0 。启动开关用一个开关表示。进水、排水、洗衣马达、脱水马达及报警分别用一个发光二极管表示。本实验只需用可编程并行接口电路的A口。其硬件接口如下图所示。也可采用可编程逻辑器件进行设计。 -Design of an automatic washing process controller, after commencement of advanced water, and so on to reach the high water mark, start laundry motor rotation 4min, such as in laundry water level lower than that found during the high water mark, then the motor stops rotating laundry and alarm, and the the water level reaches the high water mark again to start the motor. Laundry is started after the end of the drainage switch, when the water level reaches the low water level, then start the dehydration motors, rotating 2min. Repeat three times, each action requires the interval between the 2s. High water, low water level as water level sensors, with two analog switches, when the water