一个集合DS18B20的多路温度测量系统,加上adc0809数据采集,加上1602液晶显示的综合数据处理系统,有较高学习价值....

LT_1B msp430开发板例子程序－WDT2

其中的usb端口通信已经作为一个模块来使用，用户只需用以下函数就可以对usb端口进行方便地读写： unsigned char D12_WriteEndpoint(unsigned char endp, unsigned char len, unsigned char * buf) 此为usb端点输出函数，endp是要进行通信的端点，取值为3（普通端点，最大可一次传输16byte）或5（主端点，最大可一次传输64byte）；len为一次输出数据长度；*buf为数据所在位置。 usb端点数据的读操作是由底层函数自动完成的（相关函数为unsigned char D12_ReadEndpoint(unsigned char endp, unsigned char len, unsigned char * buf)； 相应端点为2和4），所读到的数据存于GenEpBuf[]（普通端点）、MainEpBuf[]或EpBuf[]（主端点）中，用户可以直接读取使用。-Usb port communication which has been used as a module, the user can use the following function on the usb port can easily read and write: unsigned char D12_WriteEndpoint (unsigned char endp, unsigned char len, unsigned char* buf) This is the endpoint usb output function, endp is to communicate the endpoint, the value for 3 (common endpoint, the first transmission maximum 16byte) or 5 ( the main endpoint, the first transmission maximum 64byte) len Length of output data for the first time * buf location for data. usb endpoint data is read

I2C总线存储器24c02驱动程序（KEIL）-memory 24c02 I2C Bus Driver (KEIL)

该程序实现有两个单片机进行环境温度和关照信息的采集。-The program has two microcontrollers to achieve environmental temperature and care information collection.

芯片PCF8951共有四个A/D输入通道：AD0，AD1，AD2，AD3,分别与四个电位器(R1,R2,R3,R4)连接，用以调节电位器的输出电压。其中AD0通道既可测量电位器输出电压，也可用于测量从J1插座输入的外接电压，须用开关J2加以选择。J4插座提供由PCF8591输出的时钟方波信号。SAA1064驱动四个数码管显示一路AD转换后得到的数据。-PCF8951 chip, there are four A/D input channels: AD0, AD1, AD2, AD3, respectively, with four potentiometers (R1, R2, R3, R4) connected to regulate the output voltage potential. AD0 channel which can be measured potentiometer output voltage can also be used to measure the input from the J1 socket external voltage, to be used to select switch J2. J4 socket output from the PCF8591 clock square wave signal. SAA1064 drivers of four digital display along after AD conversion data.

jg1223f LCD显示器的资料和C驱动源码-jg1223f LCD display, and C-driven information source

插入式系统初步编程，取

完整的c程序，包括模拟量输入输出，pid算法，触摸屏通讯等。-Complete c procedures, including analog input and output, pid algorithm, touch-screen communications.

单片机c语言 初学者有用 有例子哦-SCM c language for beginners there are examples of useful oh

自己写的 STM32 串口UART驱动, 不用固件库。超级终端界面按键时,自动回送。 应用范围: 因为不涉及IO口,所以此工程在STM32F1xx的任何主板上都可以运行。 编译器: IAR ARM 4.42A。 作者: w123456xy@sohu.com 15189792379。 -Write your own STM32 serial UART driver, no firmware library. HyperTerminal interface button, automatically send back. Application scope: because they do not involve IO port, so this works on any STM32F1xx motherboard can run. Compiler: IAR ARM 4.42A. Author: w123456xy@sohu.com 15189792379.