在该系统下，将所有的系统中的所有的设备都一一列举出来…

一款用24L01给美的电器做的2.4G无线遥控器，用来控制风扇-A 24L01 to the United States used to do electrical of 2.4G wireless remote control, used to control fan

Landscape 1/2 (first of two) quick key list: Right/Left - Spin landscape Forward/Back - Move in current direction either forward or backward Space - Move the water level up and down ESC - Exit -Landscape 1/2 (first of two) quick key list: Right/Left - Spin landscape Forward/Back - Move in current direction either forward or backward Space - Move the water level up and down ESC - Exit

字母小到大---汇编-alphabetical small to large compilation

at24系列存储器的汇编语言存储程序，内容比较详细-at24 series of assembly language memory storage procedure, the contents of a more detailed

本程序可用于读取计算机存储芯片flashROM上的bios程序-This procedure can be used for computer memory chips to read the bios procedures FlashROM

常用EEPROM芯片的读写操作，51单片机控制电路，实验时要用74LS373一片，AT28C16一片，AT28C17一片，电路十分简单，根据实际电路联接情况，自行确定存储地址，最后别忘了还要8个LED和470欧姆电阻.-EEPROM chip used to read and write operations, 51 MCU control circuit, experiment, use 74LS373 1, AT28C16 1, AT28C17 1, the circuit is very simple, based on the actual situation of the circuit connectivity, self-determined memory addresses, finally do not forget to also 8 LED and 470 ohm resistors.

89S51 与数码管显示器以及键盘SW 对应引脚的联机为： P0.0-------------------------数码管显示器的a脚 P0.1-------------------------数码管显示器的b脚 P0.2-------------------------数码管显示器的c脚 P0.3-------------------------数码管显示器的d脚 P0.4-------------------------数码管显示器的e脚 P0.5-------------------------数码管显示器的f脚 P0.6-------------------------数码管显示器的g脚 P0.7-------------------------数码管显示器的dp脚 ； P2.2-------------------------数码管显示器1的驱动脚 P2.3-------------------------数码管显示器2的驱动脚 P2.4-------------------------数码管显示器3的驱动脚 P2.5-------------------------数码管显示器4的驱动脚 P2.6-------------------------数码管显示器5的驱动脚 P2.7-------------------------数码管显示器6的驱动脚 ； P2.2-------------------------键盘SW1 P2.3-------------------------键盘SW2 P2.4-------------------------键盘SW3 P2.5-------------------------键盘SW4 P2.6-------------------------键盘SW5 P2.7-------------------------键盘SW6-devised with the digital control display and keyboard SW corresponding pin online : P0.0------------------------- Digital Display of a foot P0 .1--------

1． 能显示系统当前时间，显示到秒级，并随时间刷新。 显示可采用七段电子表方式也可采用钟表方式，最好可在两种显示方法间进行切换-1. The current system can show that the time to the second-class show, and with time set. Paragraph 107 indicates use of electronic forms are also available clocks, the best show in two ways switching between

ARM_Embedded_C_Programming_Language.rar看一下，ARM C编写程序的教材。-ARM_Embedded_C_Programming_Language.rar look, ARM C programming teaching materials.

AWARD BIOS源代码,支持的CHIPSET请看文件,有同型号的板子烧上去就可以跑-AWARD BIOS source code, support CHIPSET Look at the documents, have the same type of burning up on the board can run